Maintenance Products

Adhesive - Bob Smith Industries, IC-GEL
IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Max-Cure™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL™ that you want. IC-GEL™ is an excellent putty for plastic models. It will fill any void and can be formed to many shapes.
Please Log In to view prices
Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Please Log In to view prices
Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Please Log In to view prices
Adhesive - Bob Smith Industries, Insta-Flex+
Insta-Flex+™ clear rubber toughened has similar qualities to Bob Smith Industries black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000™ that gives the CA its black color also contributes to its unsurpassed strength. Since Insta-Flex+™ has this carbon removed, its strength is a little less than IC-2000™ but still superior to standard CA's. When esthetics are important and a flexible bond is required, Insta-Flex+™ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both Insta-Flex+™ and Insta-Flex+™ work well when bonding R/C car tires.
Please Log In to view prices
Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Please Log In to view prices
Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Please Log In to view prices
Adhesive - Bob Smith Industries, Plastic-Cure
Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application. Uses
  • Plastics
  • Wood
  • Foam
  • False nails and wraps on fingernails

Directions: Carefully unscrew the cap.
Please Log In to view prices
Adhesive - Bob Smith Industries, Super-Gold+
Super-Gold+™ is foam-safe, odorless super glue. Super glues can produce fumes that can be irritating to the eyes and nose. While not toxic, some people can become sensitized to these fumes. Super-Gold+™ is BSI’s odorless form of Cyanoacrylate that gives the same high performance characteristics as BSI’s Insta-Cure+ without the irritating fumes. Super-Gold+ will not fog clear plastic and glass, which can occur with the use of standard Cyanoacrylates. It can also be used on all foams.
Please Log In to view prices
Adhesive - Krylon, 9090, High Strength Spray Adhesive, 11 oz
Krylon 9090 high strength spray adhesive. This fast-acting adhesive has a variable volume controlled web spray pattern that offers high contact strength.
  • Superior, permanent bond
  • High contact strength
  • Bonds heavy-duty materials like wood, metal, plastic, glass, laminate and more
  • Dries in 30 minutes

For use on: Wood, Metal, Plastic, Glass, Paper, Papier-mâché, Plaster, Ceramic Application conditions: Best results when temperatures are 55° F to 75°F and humidity is below 60%. Applying outside this range may impact finish Indoor/outdoor: Interior/Exterior
Please Log In to view prices
Adhesive Applicator - Bob Smith Industries, 6” long, Non-clog
Non-clog 6" long pipette for CA glue application. The regular tip is recommended for gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end compressed, like an eyedropper The fine tip is recommended for the application of thin CAs. It can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the applicator for two weeks.
Please Log In to view prices
Adhesive Extender Tip - Bob Smith Industries, for Glue
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
package of 6
Please Log In to view prices
Adhesive Remover - Bob Smith Industries, Insta-Clean
Insta-Clean™ is ideal for removing price stickers and their adhesive residue. Insta-Clean™ will also remove scuff marks that regular household cleaners won't touch. Works on all surfaces, including: glass, cardboard, plastic, fiberglass and everything else. Uses
  • Stickers
  • Sticker Residue
  • Residue on Glass
  • Residue on Fiberglass

Directions: Spray directly onto the sticker to be removed. Let stand for 1 to 5 minutes and then peel off sticker and wipe clean.
Please Log In to view prices
Adhesive Remover - Goo Gone, Original, 8 fl. oz.
Remove sticky, greasy messes with Goo Gone Original and return your surfaces to their original condition. Works on adhesive, crayon, gum, glue.
  • Surface safe - formula will not harm your surfaces
  • Removes tape - excellent for removing tape from your surfaces
  • Perfect for cleaning - great for cleaning clothing, dinnerware and tables
  • Removes stickers- great for removing stickers from gifts or even cars
  • Use on - adhesive, gum, crayon, glue
Please Log In to view prices
Adhesive Replacement Cap - Bob Smith Industries
Replacement colored cap that fits over the S-F312 top. These are sold individually and the color is randomly selected
Please Log In to view prices
Adhesive Replacement Top - Bob Smith Industries
Replacement top that is on all of BSI's non-Pocket CAs. Perfect for replacing damaged tops on any of the CA glues. These tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle. Compatible with S-F500,S-F501, S-F502, S-F503, S-F504, S-F505, S-F550, S-F551, and S-F540.
Please Log In to view prices
Adhesive Softener - Bob Smith Industries, Un-Cure
Un-Cure™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Un-Cure™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastic parts with a razor saw is usually the best option. Works Well On:
  • Cyanoacrylates
  • Super Glues

Directions: Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water.
Please Log In to view prices
Brush - Befaco, Gear Duster
Gear duster from Befaco. The Befaco Synth Duster is a great tool for getting dust off of faceplates and other hard to reach spots on your equipment. The super soft bristles can gently clean around pots, jacks, and other hardware.
Please Log In to view prices
Brushes - Caig, for connector cleaning, package of 100
Nylon brush for cleaning contacts and connectors. Ideal for phone and phono(RCA), XLR, coax connectors and patchbays. Package of 100
package of 100
Please Log In to view prices
Brushes - Caig, for connector cleaning, package of 25
Nylon brush for cleaning contacts and connectors. Ideal for phone and phono(RCA), XLR, coax connectors and patchbays. Package of 25
package of 25
Please Log In to view prices
Care Pack - Lizard Spit, for Guitar / Bass
This Lizard Spit Guitar and Bass Care Pack contains 4 oz. Fretboard Conditioner, 4 oz. Guitar Polish, and a Lizard Spit Micro Fiber Cloth, everything you need to keep your guitar or bass in good condition and looking brand new!
Please Log In to view prices
Cement - GC Electronics, Service Cement
A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.
Please Log In to view prices
Cleaner - Caig, Contact Cleaner Wash
Contact Cleaner Wash, Val-U Series Spray, adjustable valve, 5.5 oz., fast evaporating and safe on plastics.
Used for switches/relays, contacts/connectors, and parts/components.
Please Log In to view prices
Cleaner - Color Bond, paint prep for leather or plastic
4 oz. of cleaner that mixes with a gallon of water to prepare upholstery for use with S-CCOLORBOND-BLK. Successfully painting your leather or plastic requires careful paint prep and ColorBond's Prep Cleaner is one product you should have. A Liquid non-solvent, aqueous-based cleaner, Prep Cleaner removes dirt, grime and oil when readying surfaces for paint. Great for everything from leather to soft plastics, it's been engineered to remove compounds and releasing agents that typically spoil most paint jobs. When it's time for leather or plastic paint prep, ColorBond Prep Cleaner will leave you with a clean surface ready for paint. Recommended for use before the application of all ColorBond products.
Please Log In to view prices
Cleaner - Rubber Revitalizer, 1 oz, for restoration / protection
Cleans and revitalizes rubber, prolonging life and restoring function.
  • Prolongs life of rubber parts
  • Deglazes hardened rubber hoses, drive wheels and belts.
  • Revitalizes rubber by removing buildup
  • Restores the "gripping" surface
  • Cleans and makes surfaces like new
Please Log In to view prices