2-pole 1/4" professional right-angle phone plug, gold contacts, black shell. Large jaw cable clamp for use with cable with an outer diameter of 5.5mm to 6.5mm.

PCB and parts kit for the Iss 2 fuzz built in the style of a BC183KA Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. For the BC183KA style parts kit, a pair of BC183A transistors are included.

Kent is one of the foremost pickup designers in the industry, and years of listening to what the customer wanted to hear has culminated in the esteemed Kent Armstrong pickups. With his pickups, Kent has one goal in mind: to give every player their dream sound. Faithfully recreated from the famous 1957 Patent Applied For design humbucking pickup with the same plain enamel 42 AWG wire and Alnico 2 magnets for the warmth and singing tone the originals are known for. Proper 49.2mm pole piece spacing, braided wire with no tap and maple spacers. For the first time you can get a true calibrated set for neck and bridge position but the options don't stop there.

This Luthier's Digital Caliper has a custom jaw notch for accurately measuring fretwire crown height (the height above the fretboard). This is essential for comparing new wire to original wire. And there's a notch on the depth gauge to measure fret height on the instrument.

• Measures fret height before AND after fret installation
• Accurate readouts in inches or millimeters
• A must for all precision guitar work

The TL-Classic neck is an authentic take on the tele neck pickup. With Alnico 5 rod magnets, vulcanized fiberboard flatwork, and a long skirted cover, the TL-Classic neck offers a truly vintage experience. This pickup is wax potted for sonic stability and uses cloth pushback wire for an easy and clean install. Mounting screws and springs are included. Made in Japan.

Easy to use cable tie gun cuts ties up to 50 lb. tensile. Use this tool to pull ties tightly and then cut the excess length.

Amphenol "T-Series (Pro Range)" Phone Plug. 1/4" Mono straight plug with large Jaws cable clamp, metal backshell and black finish. Internal cable clamp fits cable outer diameters ranging from 0.236” to 0.295” (6 mm to 7.5 mm).

Kent is one of the foremost pickup designers in the industry, and years of listening to what the customer wanted to hear has culminated in the esteemed Kent Armstrong pickups. With his pickups, Kent has one goal in mind: to give every player their dream sound. Faithfully recreated from the famous 1957 Patent Applied For design humbucking pickup with the same plain enamel 42 AWG wire and Alnico 2 magnets for the warmth and singing tone the originals are known for. Proper 49.2mm pole piece spacing, braided wire with no tap and maple spacers. For the first time you can get a true calibrated set for neck and bridge position but the options don't stop there.

Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features

• Primary: 4000 turns, #41 wire (lugs 4 & 2)
• Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
• Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
• Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
• Lamination Core Size: 5/8" x 1/2"
• Weight: 7 oz.

Developed in response to requests from the Collins Collectors Association"this is a matching audio transformer for older equipment with 600 ohm audio outputdriving modern speakers. Or for "classic" high impedance speakers used with newer equipmentsimply swap primary for secondary (ie...4 or 8 ohm input and 600 ohms out). Key Features Isolation unit: (i.e.

The Zero Glide® Replacement Nut System borrows the “zero fret” concept to reduce string contact in the nut by up to 93%, increasing tuning stability, playability, and open string tone. It only takes a few minutes to install with absolutely no permanent alteration to your instrument. Zero fret wire included (multiple sizes). Comparison Standard Nut Zero Glide Open String Tone Absorbs energy. Fret reflects energy, making the open strings more vibrant. Tuning Friction causes string binding. 93% less surface area. More accurate tuning. String Bend/Whammy Bar Whammy bars and string bends cause the strings to bind in the nut and not return to pitch Reduces string binding and "returns to zero" after every tug of the whammy bar or bend Durability Slots wear down over time. Minimal wear.

The HB-Classic is a vintage style humbucker pickup. It uses a made in USA Alnico 4 bar magnet which offers a uniquely balanced tone for an alnico magnet. This pickup is wax potted for sonic stability and uses a shielded 4 conductor wire for various wiring options. The HB-Classic comes in various open and covered options to match the look of any guitar. Mounting screws and springs are included. Made in Japan.

Durable heavy duty nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.
• 8 inch length
• 40 lb tensile strength

Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.

• Horizontal mount. For Vertical Mount, see P-T263-X
• Primary 117 VAC, 50/60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).
• For Vertical Mount, see P-T263-X

Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces (epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.

Includes: 3 pole, 4 position rotary switch (3P4T), 1/4" output jack and black chicken head knob. Hammond 1600 series transformers all provide secondary impedances of 4, 8, or 16 ohms but due to the unique wiring of the secondary, the impedance cannot be changed without rewiring... Until now. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary.

The ST-Classic is an amazing homage to the 1960’s strat pickup. With staggered Alnico 5 rod magnets, vulcanized fiberboard flatwork, and enamel coated wire, the ST-Classic offers a truly vintage sound. These pickups are wax potted for sonic stability, feature a bevel on the magnets, and use cloth pushback wire for an easy and clean install. A cover, mounting screws and springs are included. Made in Japan.

PCB and parts kit for the Iss 1 fuzz built in the style of the standard germanium Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

Introducing the new Pure Tone high definition mono 1/4 audio plug. This mono plug is constructed of the finest materials and will reproduce the cleanest and clearest possible signal to your audio path. The positive or tip connection is constructed of a solid nickel-plated beryllium copper rod that makes contact directly with the wire itself when inserted. With its straight and direct path from wire to tip, this new design gives you the most direct sound without traveling through additional inferior metals that alter the purity of its sound. The plug also has a set screw to aid in proper soldering when assembling. The rubber boot end will snugly fit up to 8 mm diameter cabling. If you are looking for a cleaner, Hi-Fi sound with less muddied highs and lows, the pure unaltered signal here is nothing less than stellar.

PCB and parts kit for the MKII fuzz pedal. This is based on the classic stripboard Tone Bender Professional. This stipboard fuzz circuit was also used in some versions of the Supa Fuzz as well as some other fuzz pedals. This kit includes all of the resistors, capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

XLR 3 pole female, stamped gold plated contacts, black finish. Features:

• Unique Australian designed shell and housing
• Ergonomic stylish sleeve design for improved grip
• Oversized latch lever preserves your thumb
• Leading first mate last break pin 1 on socket connectors
• Chuck style cable clamp to suit 3mm - 8mm (0.118" - 0.314") cable
• Overmolded cable support boot
• New socket contact design for improved contact resistance
• Precision machined pin contacts
• Compact 2.5mm (14AWG) solder buckets to reduce soldering time and

Vintage style ABR bridge. Wired. Hardware included The saddles on this ABR bridge are held in place with a thin wire securing the intonation screws and saddles into the frame. Adjustable in height with thumbwheels and threaded rod that uses no body inserts just as the vintage originals were designed.

• Thumbwheels and threaded rod included
• Made In Korea

Very flexible, high flame retardant polyolefin heat shrink tubing. Unheated outer diameter of about 7.6 mm with a 2:1 shrink ratio. Resistant to common liquid solvents with excellent physical, chemical, and electrical performance.