Transformers & Chokes

- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Please Log In to view prices

- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Please Log In to view prices

Features
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
Please Log In to view prices

- Vertical Mount. For Horizontal Mount, see P-T263-Z
- Primary 115 VAC, 60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
Please Log In to view prices

Specifications
- Power: 8 W
- Primary Impedance: 5,000 Ω single-ended
- Secondary Impedance: 8 Ω
- Primary DC Resistance (Red to Blue): 230 Ω
- Mounting Centers: 2.375"
- Mounting Type: U-bracket
- Weight: 0.7 lbs
Please Log In to view prices

Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Please Log In to view prices

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Please Log In to view prices

Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
Features:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
Please Log In to view prices

Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000
Please Log In to view prices

Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Please Log In to view prices

- Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.
Please Log In to view prices

- Replacements for Marshall amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Please Log In to view prices

- Replacements for Marshall Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Please Log In to view prices

- Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
- Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
- For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
- Open style with minimum 12" long primary & secondary leads leads.
- All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
- Primary impedance range from 2,500 to 10,000 Ohms.
- Secondary impedance range from 4 to 32 Ohms.
Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)
A
B
C
D
E
G Mtg.
Please Log In to view prices

- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
Please Log In to view prices

Small 42TM018 audio transformers with a 10KΩ:600Ω impedance. This transformer is a popular choice for pickup simulators in various effects such as fuzz pedals. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.
Please Log In to view prices

Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs
Please Log In to view prices

- Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.
Please Log In to view prices

- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Please Log In to view prices

Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".
Please Log In to view prices

- Designed for drop in replacement of original units. Upgraded units with variable voltage.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- See P-T290-FENDER-120 for 120 V basic transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Please Log In to view prices

Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
Please Log In to view prices

- Primary 115 VAC, 60 Hz.
- Designed for small power or bias supplies, test equipment, preamps etc.
- Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
- Economical , two hole, channel bracket, chassis mount.
- Minimum 5" long leads.
- Convenient 6.3 filament/auxiliary winding.
Please Log In to view prices

- Primary Voltage: 120 V
- Secondary 1: 140 V @ 100 mA
- Secondary 2: 28 V @ 20 mA
- Secondary 3: 10.5 V @ 2 A
Primary voltage = black wires Secondary 1 = Red wires Secondary 2 = Yellow wires Secondary 3 = Green wires
Please Log In to view prices