You are here

Transformers & Chokes

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(38 pages)
P-T850HAAudio Transformer - Hammond, 150/600Ω, Line Isolation

Special Order Item

  • 150/600 Ohm Primary Impedance
  • 300/1200 Ohm Secondary Impedance
  • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware.
  • Sealed case and wax potted core internally for stable characteristics and long life.
  • Wide frequency response ± 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.)
  • Insertion loss of apx. 1 db.
  • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance.
  • Distortion is apx. 1.5% @ 20 Hz. under full power.
  • Electrostatic shield between pri. & sec. connected to the green lead.
  • Humbucking construction
  • Balanced split windings on pri. & sec. for circuit versatility. Primary may be used as a secondary and vice versa for impedance matching.
  • Lead length: Min. 4"

Please Log In to
view prices
Click to read more
P-T1630SEAAudio Transformer - Hammond, 30W, 3.5kΩ, 42H, Tube Output

Special Order Item

  • "Over designed" for high fidelity, single ended, Class-A, tube output circuits (triode, tetrode or pentode tubes).
  • Enclosed (shielded), four slot, chassis Type "X" mounting.
  • Frequency response at least 20 Hz. to 20 Khz. at full rated power (+/- 1 db max., ref. 1 Khz.)
  • Insulated flexible leads 8" min.
  • For maximum versatility, all units include a 40% screen tap for Ultra-Linear, tetrode/pentode operation (if desired).
  • High quality laminations, (M6) grain oriented silicon steel.
  • Core is gapped to reduce core saturation in Class-A tube amplifier circuits.
Please Log In to
view prices
Click to read more
P-T1650PAAudio Transformer - Hammond, 60W, 6.6kΩ, Push-Pull Tube Output

Special Order Item

  • Designed for push-pull tube output circuits.
  • Units are designed to provide ample "headroom" at bass frequencies
  • Has a secondary tap for 4, 8 or 16 ohm outputs.
  • Enclosed (shielded), 4 slot, above chassis Type "X" mounting.
  • Manufactured with plastic coil forms for coil support and insulation.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz) minimum.
  • Insulated flexible leads 8" min.
  • Includes 40% screen taps for Ultra-Linear operation (if desired).
  • Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output.
Please Log In to
view prices
Click to read more
P-C1536XChoke - 0.17 - 250, Heavy Duty Hash Choke
Molded powdered iron core.
1-1/4 long axial leads.
High inductance & high current.
L measured at 1 Khz. Inductance: 250 µH20% tolerance
DC resistance ohms: .17
Self Resonant Frequency (MHz): 1.5
Maximum DC current amps: 2.5
Coil diameter (in): .43
Core Length (in): 1.25
Please Log In to
view prices
Click to read more
P-C194BChoke - Hammond, for Fender Bandmaster, Dual Showman, etc.

Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:



  • Inductance ± 15%: 4 H
  • D.C. Current: 90 mA


Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs.

Please Log In to
view prices
Click to read more
P-C194AChoke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications:



  • Inductance ± 15%: 4 H
  • D.C. Current: 50 mA


Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs.

Please Log In to
view prices
Click to read more
P-C194GChoke - Hammond, Replacement for Marshall Plexi

Replacement for Marshall Plexi Specifications:



  • Inductance ± 15%: 3 H
  • D.C. Current: 250 mA


Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Please Log In to
view prices
Click to read more
P-C194CChoke - Hammond, replacement for Marshall Plexi JCM800
Replacement for Marshall Plexi JCM 800.
Specifications:
  • Inductance ± 15%: 40 H
  • D.C. Current: 50 mA
Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Please Log In to
view prices
Click to read more
P-C194DChoke - Hammond, Replacement for Vox AC30 reissue
Replacement for Vox AC30 reissue
Specifications:
  • Inductance ± 15%: 5 H
  • D.C. Current: 150 mA
Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Please Log In to
view prices
Click to read more
P-C194EChoke - Hammond, Replacement for Vox AC30 vintage
Replacement for Vox AC30 vintage
Specifications:
  • Inductance ± 15%: 30 H
  • D.C. Current: 100 mA
Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Please Log In to
view prices
Click to read more

Pages

(38 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Transformers & Chokes