You are here

Transformers & Chokes

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(15 pages)
P-TM45PTransformer - Marshall Replacement, Power for JTM45

Replacement power transformer for Marshall JTM45.


Please Log In to
view prices
Click to read more
P-TN-68XTransformer - Line Isolation, 50 VA, 115V, 435 mA, 2 x 115V

An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.


Please Log In to
view prices
Click to read more
P-T166X-36Transformer - Hammond, Low Voltage / Filament, Open, 36 VCT

Special Order Item

  • Primary 115 VAC, 60 Hz.
  • Secondary 36 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).

Please Log In to
view prices
Click to read more
P-T167X-25Transformer - Hammond, Low Voltage / Filament, Enclosed, 25 VCT

Special Order Item

  • Primary 115 VAC, 60 Hz.
  • Secondary 25 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).

Please Log In to
view prices
Click to read more
P-T187XTransformer - Hammond, Low Voltage, Single Primary, 120VCT

Special Order Item

  • Single Primary 115VAC
  • Operates on 50/60 Hz.
  • Combination solder or quick connect terminals.
  • Split bobbin construction eliminates the need for an electrostatic shield.
  • Hi-pot tested to 2 KV RMS.
  • Economical open style, channel frame - chassis mount design
  • UL recognized & CSA certified.

Please Log In to
view prices
Click to read more
P-T260XTransformer - Hammond, Plate & Filament

Special Order Item

  • Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
  • Designed for preamps, low power amps, general replacement, test equipment, etc.
  • Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
  • Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
  • Minimum 5" long leads.
  • For more selection check out our P-T300-X series of universal plate & filament transformers.

Please Log In to
view prices
Click to read more
P-T710-XTransformer - Hammond, High Voltage Plate, 115 VAC, 50 / 60 Hz

Special Order Item

  • Primary 115 VAC, 50 / 60 Hz.
  • At 2,000 VAC and above, secondary leads are through rubber bushings
  • Units can be run full wave bridge or full wave C.T.
  • V.A. is a C.C.S. rating
  • Current ratings are CCS (Continuous Commercial Service) & ICAS ratings (Intermittent Commercial or Amateur Service).
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Class A insulation (105 degrees C).
  • Hi-Pot test at a minimum of twice secondary voltage
  • Conservative designs - CSA certified (209651).

Please Log In to
view prices
Click to read more
P-T164X-28Power Transformer - Hammond, 115V, 28VCT

Special Order Item

  • Both series operate on 50/60 Hz current
  • Low profile, split bobbin design.
  • Dual winding secondaries, non-concentrically wound
  • Units are designed so that all windings must be used
  • Low primary to secondary coupling - no electrostatic shield required.
  • High insulation - Hipot of 2,500V RMS.
  • Class B insulation - 130 degrees C.
  • c UL us recognized

Please Log In to
view prices
Click to read more
P-T167G120Transformer - Hammond, Low Voltage / Filament, Enclosed, 120 VCT

Special Order Item

  • Primary 115 VAC, 60 Hz.
  • Secondary 120 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).

Please Log In to
view prices
Click to read more
P-T125JTransformer - Hammond, Output, 8 W, 2.5k or 4k Primary

Special Order Item

Specifications Audio Watts: 8 Primary Impendance (Ohms): 2.5k/4K center-tapped Secondary Impendance (Ohms): 6/8 - 3.2/4 Mounting centers: 2-13/16u-bracket Weight: 1.0 lb.


Please Log In to
view prices
Click to read more

Pages

(15 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Transformers & Chokes