Transformers & Chokes

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. Sealed case and wax potted core internally for stable characteristics and long life. Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.) Insertion loss of apx. 1 db.

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with hardware. Includes wire leads (minimum length of 4"). Frequency response +/- 0.5 db max. from 50 Hz. to 15 Khz. Insertion loss of apx. 1 db. Maximum power level +15 dbm. (except 841A, 842A & 844A which are +20 dbm) with specified characteristics, or higher levels with reduced low frequency performance.

• Replacements for Yorkville/Traynor Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Primary 115 VAC, 60 Hz.
• Secondary 12 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 10 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

Features:

• Perfect for audio input, line matching, isolation or output transformer applications.
• 2 watt (± 1.5 dB, 300 Hz. - 50 kHz.).
• Epoxy potted in an attractive black molded case, Pin type P.C. board mount (min. 0.187" length).
• Power level ratings are maximum at lowest frequency rating
• Power can be increased slightly at higher frequencies.
• Will withstand soldering for 10 sec. @ 260 degrees C, ambient temp. 85 degrees C max.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 16V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 25 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

Capacity: 100 VA
Features:

• Primary 115VAC, 60 Hz.
• Secondary taps @ 90, 100, 110, 115, 120 & 130VAC
• Electrostatic shield between primary & secondary
• Connection by flexible leads, 8" minimum length
• Perfect for critical line voltage needs (examples: older "classic" tube equipment or Japanese 100V equipment).
• CSA certified (# LR3902)
• Remember - These units do NOT convert line frequency

• Single Primary 115VAC
• Operates on 50/60 Hz.
• Combination solder or quick connect terminals.
• Split bobbin construction eliminates the need for an electrostatic shield.
• Hi-pot tested to 2 KV RMS.
• Economical open style, channel frame - chassis mount design
• UL recognized & CSA certified.

Specifications:

• Size: 18 VA
• Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
• Secondary VAC RMS Series: 36V @ 0.5 A
• Secondary VAC RMS Parallel: 18V @ 1 A

Features:

• Primary 117/234 VAC, 50/60 Hz.
• Dual secondaries
• Secondaries can be used as; a center tapped secondary, parallel connected or used individually
• Units are designed for use with all windings engaged.
• Open style.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C) for extra

Specifications:

• Size: 50.4 VA
• Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
• Secondary VAC RMS Series: 12.6V @ 4 A
• Secondary VAC RMS Parallel: 6.3V @ 8 A

Features:

• Primary 117/234 VAC, 50/60 Hz.
• Dual secondaries
• Secondaries can be used as; a center tapped secondary, parallel connected or used individually
• Units are designed for use with all windings engaged.
• Open style.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C) for ex

• Replacement for Ampeg amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Part No.
Primary
Ampeg Model Names
Ampeg Part No
Bobbin/Paper Wound


VAC
Hz.




P-T291GX
120 V
60 Hz.
B25
12XA
Bobbin


P-T290CAZ
117 V
60 Hz.
Gemini VI 25W
PT 113
Bobbin


P-T290ETX
120 V
60 Hz.
Super Echo Twin
PT 109
Bobbin


P-T291HX
110 / 115 / 230 V
50 / 60 Hz.
V50H
94-270-030
Bobbin

Dual 117/234 VAC primary, 50/60 Hz. operation. 12 V series, 6 V parallel secondary.mary, 50/60 Hz. operation.

Dual 117/234 VAC primary, 50/60 Hz. operation. 30 V series, 15 V parallel secondary.

Dual 117/234 VAC primary, 50/60 Hz. operation. 48 V series, 24 V parallel secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and a 100V center tapped secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and a 22V center tapped secondary.

Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and a 14V center tapped secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and an 8V or 8.5V secondary.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 12V secondary.

Studio grade frequency response: 20 Hz. - 20 Khz. (+/- 1 db, ref. @ 1 Khz.) minimum. Excellent frequency response utilizing a 80% nickel core providing high permeability combined with low losses. Designed for maximum bandwidth, lowest distortion at +10 dbm power level or less. Plated steel cans, adjustable height case bracket.

The PRC-1 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.

The PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.