You are here

Transformers & Chokes

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(15 pages)
P-C194AChoke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Please Log In to
view prices
Click to read more
P-T290-FENDERTransformer - Hammond, Guitar Amplifier, replacement for Fender

Replacement for Fender Champ, Vibro Champ, Princeton, Princeton Reverb, Tweed Deluxe Equivalent to Fender part number 125P1B & 022772 Primary:120 VAC, 60 Hz. For 240V version, see P-T290AEX Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Plastic Core
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.


Please Log In to
view prices
Click to read more
P-TF22913Transformer - Replacement for Fender®, Output, 12W, 8Ω
Generic replacement for Fender Princeton Reverb, Tweed Deluxe, 8 ohms. Transformer is not manufactured by Fender, but is equivalent to #125A10B & #022913.




Specifications


Audio Power
12 W (RMS)


Primary Impedance
8,000 Ω


Secondary Impedance
8 Ω


Mounting Centers
2.875"


Mounting Type
Vertical


Weight
1.0 lbs




Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Please Log In to
view prices
Click to read more
P-TF22871Transformer - Fender® Replacement, Output, 50 W, 4 Ohm

Replacement for Bassman heads. Equivalent to #125A13A & #022871.


Please Log In to
view prices
Click to read more
P-TM9100OTransformer - Marshall, Output, 100 W, for JCM900

Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.


Please Log In to
view prices
Click to read more
P-T166X-6D3Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 6.3 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).

Please Log In to
view prices
Click to read more
P-T125XSETransformer - Hammond, Universal Single Ended
  • Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
  • Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
  • For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
  • Open style with minimum 12" long primary & secondary leads leads.
  • All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C.

Please Log In to
view prices
Click to read more
P-T300-XTransformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
  • Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
    • NOTE: units are designed to operate with BOTH primary windings engaged.
    • See primary wiring information under resources.
  • Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
  • Highpot tested: 2,000 VAC
  • Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
  • Windings: Concentric wound for low stray field and low noise.
  • Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
  • Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
  • Conservative designs - CSA certified (209651).

Please Log In to
view prices
Click to read more
P-TM950OTransformer - Marshall, Output, 50 W, for JCM 900

Genuine Marshall™ output transformer for JCM900 and JCM2000.


Please Log In to
view prices
Click to read more
P-C194GChoke - Hammond, Replacement for Marshall Plexi

Replacement for Marshall Plexi Specifications:



  • Inductance ± 15%: 3 H
  • D.C. Current: 250 mA


Features:



  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Please Log In to
view prices
Click to read more

Pages

(15 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Transformers & Chokes