 | Transformer - Hammond, Output, replacement for Fender- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
| | Click to read more |
 | Filter Choke - Hammond, Open BracketFeatures
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
| | Click to read more |
 | Choke - Hammond, for Fender Bandmaster, Dual Showman, etc.Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
| | Click to read more |
 | Transformer - Hammond, High Voltage Plate & Filament, Vertical mount- Vertical Mount. For Horizontal Mount, see P-T263-Z
- Primary 115 VAC, 60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
| | Click to read more |
 | Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary- Primary 115 VAC, 60 Hz.
- Designed for small power or bias supplies, test equipment, preamps etc.
- Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
- Economical , two hole, channel bracket, chassis mount.
- Minimum 5" long leads.
- Convenient 6.3 filament/auxiliary winding.
| | Click to read more |
 | Choke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications:
- Inductance ± 15%: 4 H
- D.C. Current: 50 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
| | Click to read more |
 | Transformer - Hammond, Guitar Amplifier, replacement for FenderReplacement for Fender Champ, Vibro Champ, Princeton, Princeton Reverb, Tweed Deluxe Equivalent to Fender part number 125P1B & 022772 Primary:120 VAC, 60 Hz. For 240V version, see P-T290AEX Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Plastic Core
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
| | Click to read more |
 | Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT- Primary 115 VAC, 60 Hz.
- Secondary 6.3 C.T.
- Center tapped secondary.
- Open style, channel bracket, two hole chassis mount.
- Minimum 6" long leads.
- Dual bobbin design - no electrostatic shield required.
- Class B insulation (130 degrees, C).
- Hi-Pot test of 2,000 V RMS.
- UL listed (# E50394) & CSA certified (# LR3902).
| | Click to read more |
 | Transformer - Hammond, Universal Single Ended- Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
- Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
- For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
- Open style with minimum 12" long primary & secondary leads leads.
- All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C.
| | Click to read more |
 | Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
| | Click to read more |
480.755.4712