• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

• Replacement for Vox amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.



Specifications



Primary
120 VAC @ 60 Hz (Black - White)


Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC


Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC


Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.

Fender Original Hot Rod DeVille Power Transformer. Equivalent to #041752.

Fender Original Blues Junior Power Transformer. Equivalent to #049967.

• Horizontal mount. For Vertical Mount, see P-T263-X
• Primary 117 VAC, 50/60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).
• For Vertical Mount, see P-T263-X

Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary

• Replacements for Marshall amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

• Replacement for Yorkville/Traynor amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Part No. Primary Secondary 1 Secondary 2 Secondary 3 Yorkville / Traynor Amp Yorkville / Traynor Part No VAC Hz. P-T290TRA 120 V 60 Hz. 320 V @ 600 mA 60 V @ 50 mA 6.3 V.C.T. @ 9 A 100 Watt Bass A-1380 P-T290TRB 120 V 60 Hz. 620 V @ 115 mA 6.3 V.C.T. @ 115 mA YBA2-B A-1314 P-T291JX 120 V 60 Hz. 320 V @ 500 mA 60 V @ 20 mA 6.65 V.C.T.

• Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 12.6V center tapped secondary

• Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 120 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 6.3 filament/auxiliary winding.

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

• Primary Voltage: 120 V
• Secondary 1: 140 V @ 100 mA
• Secondary 2: 28 V @ 20 mA
• Secondary 3: 10.5 V @ 2 A

Primary voltage = black wires Secondary 1 = Red wires Secondary 2 = Yellow wires Secondary 3 = Green wires

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).