You are here

Tools

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(17 pages)
S-TCPS7Springs - Xcelite, replacement for S-TCN255
Replacement spring for S-TCN255 (Xcelite curved nose pliers).
Please Log In to
view prices
Click to read more
S-T156Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
Please Log In to
view prices
Click to read more
S-H190-XStandoff - 0.18", Adhesive
Package Quantitys Available:

Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:



  • Low profile 0.180" standoff height.
  • Offset base allows use when holes are close to the PCB edge.

Please Log In to
view prices
Click to read more
S-T8276Aligner - GC Electronics, Duplex
Butyrate shaft 6-1/8" long with 1/8" wide steel tips. Tip on one end recessed.
  • Material: Conductive Nylon Metal
  • End: 1/8"
  • End 2: 1/8"
Please Log In to
view prices
Click to read more
S-T9091Hex Tool - GC Electronics, Double End ⅛"
Molded from Delrin, 5-3/32" long. Ends are 1/8" hex with .10" wide by .02" thick plastic screw driver on one end.
Please Log In to
view prices
Click to read more
S-TWCC104Sponge - for Soldering Station
Replacement sponge for the Weller WLC 100 soldering station ( S-TWLC100 ) . Keep your iron tip clean using this genuine Weller replacement sponge. Cleaning a hot soldering iron on a damp sponge causes the solder to contract at a contrasting rate to the soldering iron, helping to remove any solder stuck to the tip. Always be sure the sponge is merely damp rather than soaked in water.
Please Log In to
view prices
Click to read more
P-PC-ST1StripBoard - Single Sided, Size 1, Uncut
Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.
Please Log In to
view prices
Click to read more
P-PC-PAD1PadBoard - Size 1, Double Sided, Plated Holes

Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.



For fastening your project to a surface see our adhesive standoffs (S-H190-X)



Features:



  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)

Please Log In to
view prices
Click to read more
S-T302Bulb - Solder Sucker
Handheld suction type solder remover.
Please Log In to
view prices
Click to read more
S-T22-XSolder wick - GC Braid, multiple sizes
5 feet Long. Great for removing solder from printed circuit boards.
Please Log In to
view prices
Click to read more

Pages

(17 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Tools