You are here

Tools

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(15 pages)
S-ZVT1000Valve Tester - Orange, VT-1000
The compact and extremely easy to use VT1000 is a fully automatic valve tester, which performs a wide range of tests quickly and accurately. The benefits of using the VT1000 are clear and wide reaching; users can quickly and simply match and test valves, plus receive a reliable health check as to whether their valves are good, bad or worn.
Orange Amps developed the world's first fully automatic, portable, digital valve tester, the VT1000, to make it easy to test amp valves. Until now testing valves with little or no knowledge of valve theory was difficult, expensive and often unreliable.
Please Log In to
view prices
Click to read more
S-MRFGENGenerator - Lodestar, RF Signal

Compact solid state RF signal generator designed for the hobbyist, service bench and technical instruction. The generator is most suited for checking and aligning the IF circuit and tuners in AM, FM, and TVs. 100 kHz to 150 MHz in 6 bands and up to 450 MHz on third harmonics.



Features:



  • Wide frequency range- 100 Khz to 150 MHz
  • With 1 KHz oscillator purpose of modulation
  • High Stability
  • Output control- 0dB/-20dB/-40dB and fine adjuster
  • Frequency accuracy + or - 5%
  • RF output- 100mV rms appx. (up to 35MHz unloaded)
  • Output control- High-low switch, fine adjust
  • Audio output 1 KHz min., 2V rms
  • Modulation: Internal: 1 KHz (AM) 30% appx., External: 50 Hz ~ 20 KHz at <1V rms input

Please Log In to
view prices
Click to read more
S-MAFGENGenerator - Lodestar, Audio Frequency

The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.


Please Log In to
view prices
Click to read more
S-TBM4-XBias Master™ - TAD, tube tester, with 4 probes

Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.


Please Log In to
view prices
Click to read more
S-T213-SETNut File - Edge-Cut, for guitar, 10 sizes
Package of 10

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.



  • 4-1/2” cutting edge
  • Double sided (both sides are the same gauge)
  • Set of 10 files
  • Made In Japan


Set contains one of each size:



  • 0.010"
  • 0.013"
  • 0.016"
  • 0.024"
  • 0.028"
  • 0.032"
  • 0.036"
  • 0.042"
  • 0.046"
  • 0.056"

Please Log In to
view prices
Click to read more
S-T262Fret Slotting Miter Box - for guiding fret saws

Use this Fret Slotting Miter Box to accurately cut fret slots with a fretting handsaw. The ball-bearing guides make sawing easier and faster; they hold your fret saw perpendicular to the fingerboard and can be adjusted to match the blade precisely. You can quickly slot any board up to 3"" (76.2mm) wide, with adjustable depth of cut for any fret wire. You always have an unobstructed view of your work.



Made of rugged aluminum and 12" (304.8mm) long, this miter box has convenient mounting holes for firm attachment to your workbench, the mounting screws and spanners are included. Instructions also included.


Please Log In to
view prices
Click to read more
S-T265Fret Leveling File - Diamond, 600 grit, Wooden Grip

600 grit diamond fret leveling file used for leveling frets and beveling fret ends. Comfortable wooden handle.


Please Log In to
view prices
Click to read more
S-T259-AFret Press - Handheld, 4 cauls

Handheld fret press is a professional fretting tool that gives you finer control over the pressure needed to seat a fret into the slot - you can actually feel it seating! It eliminates complicated clamping setups, so your press-in fret jobs go faster. There's a self-leveling upper caul that adjusts easily to any neck. Used with radius inserts (S-T261) to press frets into guitar fret boards. This method is preferred by many as an alternative to hammering the frets in. Includes 4 interchangeable support cauls.


Please Log In to
view prices
Click to read more
S-T236Fret File - 600 grit, 3 radiuses, diamond, for Crowns

600 grit diamond-plated file. 3 different, (small, medium, large) radiuses in one file. 130mm file length, 230mm total.


Please Log In to
view prices
Click to read more
S-TWSA350Bench top smoke absorber - Weller
Keep those fumes out of your face while soldering with this benchtop smoke absorber.
  • Removes flux fumes from soldering workbench
  • Great for workspaces using more active fluxes used with lead-free solder
  • Fumes are absorbed by the replaceable carbon-activated filter
  • Includes one replacement filter (S-TWSA350F)
  • Stand allows the smoke absorber to be adjusted to varying angles
  • Fan is quiet and will not add significant noise to the workspace
  • ESD safe
  • Air Flow Volume: 1370 l/min
  • Wattage: 20 watts
Please Log In to
view prices
Click to read more

Pages

(15 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Tools