Tools

Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.

Three neodymium magnets on each end to ensure a straight cut at a right angle. The saw guide can adjust 0mm to 4.7mm slot depth by sliding the frame. The slide frame side has scale marks representing 1mm of depth. For use with S-T254.

ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

I.C. hand lotion soothes dry, chafed skin caused by glove irritation and chemical contact. ESD-safe. Improves skin contact with wrist strap grounders. Contaminant-free, greaseless. Natural Non-Contaminating Static Dissipative Moisturizing Hand Lotion contains NO Silicones, Lanolin’s, Glycerin or Mineral Oils. Absorbs immediately into your skin and is greaseless. The IC Pre-gloving Moisturizer helps to relieve dermatitis, urticaria, “skin flaking”, chapping and other irritations due to regular use of gloves and will not degrade or weaken latex or Nitrile Gloves. Used in conjunction with wrist straps. Vitamins A, D & E lightly fragranced with all natural herbal steeped tea along with hints of grapefruit and lemon splashes.

• Helps to meet ANSI S20.20
• NSF E4 Certified for Food Handlers
• Static Dissipative and ESD Safe
• Helps Grounding to Wrist Straps
• CHG Compatible

Get accurate string spacing without the use of complicated tools with this easy-to-use String Spacing Ruler. "Mark outer string locations with pencil lines (high and low E strings on guitars), usually about 1/8" in from fingerboard edges. Turn ruler over (use marked side). With wide spacing toward bass side, narrow spacing toward treble side, find group of marks (six for guitar) which best fit your two pencil lines. Use a razor knife or thin mechanical pencil to mark the string positions through the ruler's slots.

Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

• Convenient pump spray (2oz.

This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.

Set of files for precision work.
Includes:

• flat
• half round
• round
• square
• three square (i.e. triangular)

The Dunlop System 65 Fret Collars include everything you need for a quick fret polish without the need for taping the entire neck. Two sizes of flexible steel collars are included, 0.125 and .080.

Atten T900 soldering iron tips. The conical style is great for all types of soldering. The pointed tip works well with small connections and the expanding cone shape allows for use with larger connections such as solder lugs. These tips are an excellent choice for use with the S-ST-2090D soldering station and S-ST-2065D soldering iron.

Keep those fumes out of your face while soldering with this benchtop smoke absorber.

• Removes flux fumes from soldering workbench
• Great for workspaces using more active fluxes used with lead-free solder
• Fumes are absorbed by the replaceable carbon-activated filter
• Includes one replacement filter (S-TWSA350F)
• Stand allows the smoke absorber to be adjusted to varying angles
• Fan is quiet and will not add significant noise to the workspace
• ESD safe
• Air Flow Volume: 1370 l/min
• Wattage: 20 watts

Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.

IC-LOC™ Blue is a medium thickness, medium strength thread lock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be disassembled with standard hand tools if required. Uses

• Threads of fasteners
• Bolts
• Screws
• Nuts

Directions: Shake well, then apply IC-LOC™ Blue to the clean and dry threaded areas before assembling non-plastic parts. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Blue is anaerobic and cures in the absence of air, which occurs when a bolt, screw or nut is tightened. IC-LOC™ Blue prevents loosening of fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Blue seals and prevents rusting of threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Remove residue with a damp cloth. Similar to Loctite Blue.

This multi-tool has everything you need to maintain your drum kit before, during, and after performances and practice sessions, from our T-Handle Drum Key to screw driver bits and hex key wrenches. Drums take a beating. Literally. That means ongoing adjustment and repair—even during a performance. That’s where the GrooveTech Drum Multi-Tool comes in. It'll quickly remedy problems on virtually all makes and models of drums and hardware, starting with a drum key that's made to the same high standards as our T-Handle Drum Key. And no multi-tool would be complete without the standard array of screwdrivers, so we provide a 5mm slotted and #1 and #2 Phillips. But where this tool really adds value is its collection of both inch and metric hex wrench sizes to handle pedals and other hardware.

(63/37 Rosin Core) - ..031" Diameter, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC™ Green wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners. Uses

• Threads of fasteners
• Bolts
• Screws
• Nuts

Directions: Shake well. Unscrew cap and cut off tip. Apply IC-LOC™ Green to clean preassembled fasteners. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Green prevents the loosening of threaded fasteners from shock and vibration by wicking into threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Locked fasteners are only removable by localized heating and hand tools. Remove residue with a damp cloth. Similar to Loctite Green.

Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.

• Sensor hole in the base of tip is fitted with a stainless steel liner
• Prevents the tip from seizing to the sensor

1.4m, Self adhesive type, 64mm width for S-T229-X sanding blocks.

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

Easy to use cable tie gun cuts ties up to 50 lb. tensile. Use this tool to pull ties tightly and then cut the excess length.

A small, easily-portable tool designed for quick adjustments of various instrument parts (including nuts and thumb wheels), from potentiometers and pickup switches to tuning machines. One end is designed for loosening, the other is designed for tightening. The device has been chamfered and polished to avoid damage to your instrument when used.

This multi-tool has everything you need to make quick, gig-saving adjustments on the fly, featuring hex wrenches, screwdrivers, and a precision ruler for tremolo, action, pickup height, and other basic tweaks using both metric and imperial units. The GrooveTech Mini-Multi Guitar/Bass Multi-Tool is designed for all those on-the-fly adjustments you might need to make when it counts the most. It comes equipped with hex wrenches, screwdrivers, and a precision ruler so that you can quickly adjust your tremolo system, action, pickup height, and other basic functions. Oh, and it comes with a super-handy bottle opener for when you need to get to that refreshing beverage after the gig. Virtually all makes and models of guitars and basses are covered. Tools are pro-grade and absolutely dependable. Don’t head to the gig without a Mini-Multi Guitar/Bass Multi-Tool in your pocket. GrooveTech Tools offer a lifetime of quality instrument care for players of all levels.

The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4.5” cutting edge
• Double sided (both sides are the same gauge)
• 10 gauges available
• Sold individually*
• Made In Japan

*See S-T213-SET for a set of all 10 sizes.