You are here

Tools

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(16 pages)
P-PC-SB404BreadBoard - Solderable PCB, 400 point pattern
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts.
The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
Please Log In to
view prices
Click to read more
S-T259-AFret Press - Handheld, 4 cauls

Handheld fret press is a professional fretting tool that gives you finer control over the pressure needed to seat a fret into the slot - you can actually feel it seating! It eliminates complicated clamping setups, so your press-in fret jobs go faster. There's a self-leveling upper caul that adjusts easily to any neck. Used with radius inserts (S-T261) to press frets into guitar fret boards. This method is preferred by many as an alternative to hammering the frets in. Includes 4 interchangeable support cauls.


Please Log In to
view prices
Click to read more
S-T248-XWood Saw Rasp - High Carbon Steel

One coarse side, one fine side.


Please Log In to
view prices
Click to read more
S-T312String Cutters - Dunlop, System 65

The Dunlop System 65 String Cutter can cut through any strings. It will cut through .130” thick bass strings just as easily as a .010” guitar string. This is a great tool to keep nearby, easily fitting in a case or gig bag.


Please Log In to
view prices
Click to read more
S-TSP40LSoldering Iron - Weller, Marksman, 40 watts
  • Weller Consumer Soldering Irons with 3 LEDs
  • Three LED lights for limited application shadowing
  • Round Co-molded soft grip handle design for easy tip positioning
  • Triangular handle area for maximum tip control
  • Stainless steel heater construction
  • Excellent quality consumer iron
  • Input Voltage: 120
  • Power Consumption: 40 watts
  • Tip Temperature: 900ºF
  • Heating Element Type: Nichrome Wound
  • Fiberglass and ceramic insulated

Please Log In to
view prices
Click to read more
S-T235Precision Router Base - Support for Dremel Tool

A stable and versatile way to support your Dremel tool. This precision router base is the best way to hold a Dremel for freehand routing, inlaying, widening fret slots, and more. Made of brass, aluminum and machined steel, it features precision cutting depth adjustment with large thumbwheels to eliminate guesswork.


Please Log In to
view prices
Click to read more
S-T306Flashlight - Dunlop, System 65 gig

The Dunlop System 65 Gig Light is a high lumen, road ready flashlight. At 3.7” in length it easily fits in a gig bag or pocket and can be safely secured with its metal belt clip. This flash light has three different modes that can be accessed by lightly tapping the power switch: high beam, low beam, and strobe. The beam can also be focused by adjusting the lens providing up to 100 yards of visible light with a tight focus. This waterproof flashlight runs on a single AA battery which is included.


Please Log In to
view prices
Click to read more
S-T42HSeizer forceps - Xcelite, 5.5" straight nose, serrated jaws

Seizer forceps. Product Features:



  • Versatile tool with unusual holding qualities
  • Clamps firmly to hold wires for soldering
  • Acts as a heat sink and retrieves small parts from hard-to-reach places
  • Precision-machined from perfectly tempered stainless steel
  • Box-joint construction
  • 3-position snap lock
  • Serrated jaws

Please Log In to
view prices
Click to read more
S-TGTSC1String Cutters - CruzTOOLS GrooveTech, for guitar and bass

CruzTOOLS developed the GrooveTech String Cutters specifically for Guitar and Bass strings. Guitar and bass strings are made of hardened stainless steel or nickel with thicknesses as high as 3mm. Ordinary diagonal cutters are designed for soft copper, and thus fail miserably when used on strings. GrooveTech String Cutters were developed specifically for this application, using a proprietary heat-treatment process. Despite its compact five-inch length, even “B” bass strings cut easily and your days of dented blades will be a thing of the past. Vinyl grips feel great in your hands.


Please Log In to
view prices
Click to read more
S-T213-SETNut File - Edge-Cut, for guitar, 10 sizes
Package of 10

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.



  • 4-1/2” cutting edge
  • Double sided (both sides are the same gauge)
  • Set of 10 files
  • Made In Japan


Set contains one of each size:



  • 0.010"
  • 0.013"
  • 0.016"
  • 0.024"
  • 0.028"
  • 0.032"
  • 0.036"
  • 0.042"
  • 0.046"
  • 0.056"

Please Log In to
view prices
Click to read more

Pages

(16 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Tools