Tools

Fret Polishing Rubber - Erases Fine Scratches & Marks
Package of 2
Make your frets shine with this fret polishing rubber. Erases fine scratches and marks. Set of 2. Because of the softness of the rubber, the polisher fits to fret arch perfectly and keeps the fingerboard damage to a minimum. Easy to cut for delicate fret work. This is a great rust remover and polisher!
Available in 1000 (tan), 400 (red), or 180 (blue) grit.
Please Log In to view prices
Alignment Kit - GC Electronics, for color TVs
Package of 6
Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:
  • 8282 Zenith type Hex/Screwdriver
  • 8606 5" Hex wrench
  • 9091 Hex iron core tool
  • 9300 5" Double sided hex tool
  • 9304 Hex screwdriver combination
  • 8608 Potentiometer Adjustment Tool
Please Log In to view prices
Soldering iron tip - Weller, screwdriver, for WTCPT, 700F
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Screwdriver Tip for TC201 Series Iron
  • PTA7 - 1.6mm / 0.063" diameter screwdriver tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
Please Log In to view prices
Feeler Gauge - 20 Sizes, for measuring gaps / clearance
Package of 20
This precise set of 20 feeler gauges in the luthier's workshop can perform a wide variety of functions to measuring with string action to measuring the correct nut slot depths, fret slot width, string to fret clearances, and other hardware installation work, these ground steel feeler gauges are marked in both metric and imperial measurements for easy use.
Please Log In to view prices
Bulb - Solder Sucker, for removing solder
Handheld suction type solder remover.
Please Log In to view prices
StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
Please Log In to view prices
Brush - Flat Chip, 2”, 1500, applicator
2 inch flat chip brush great for applying tolex glue or any other purposes. This brush features a 4.75 inch wood handle.
Please Log In to view prices
Alignment Kit - GC Electronics, for CB
Package of 8
Contains
  • 5009 Duplex no-metal screwdriver
  • 5097 K-tran tool
  • 8271 core aligner
  • 8282 Zenith alignment tool
  • 9091 hex iron core tool
  • 9440 transistor tool
  • 8276 Duplex aligner
  • 9304 double end tool
Please Log In to view prices
Chisel - Flat, Japanese, Steel, Tataki-Nomi
High quality made in Japan flat chisels for luthier work. These chisels have a blade hardness of HRC63 and a total length of 225mm. The hardwood handle features a flat end for hammering,
Please Log In to view prices
Sponge - for Soldering Station, for cleaning tips
Replacement sponge for the Weller WLC 100 soldering station ( S-TWLC100 ) and others. Keep your iron tip clean using this genuine Weller replacement sponge. Cleaning a hot soldering iron on a damp sponge causes the solder to contract at a contrasting rate to the soldering iron, helping to remove any solder stuck to the tip. Always be sure the sponge is merely damp rather than soaked in water.
Please Log In to view prices
Center Punch - Spring Loaded, Adjustable Force
Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.
Please Log In to view prices
BreadBoard - Solderless, 400 point pattern
Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
Please Log In to view prices
Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Please Log In to view prices
Springs - Xcelite, replacement for S-TCN255
Replacement spring for S-TCN255 (Xcelite curved nose pliers).
Please Log In to view prices
Tool - Helping Hand with Magnifier, 65mm, 2.5X
Magnifier with 2 ½" lens. Both clamps and magnifier can be removed. Great for precision work on circuit boards, solders and repairs. 6 ball joints for any angle. Simple to adjust thumb screws. Nickel plating fittings. Sturdy iron cast base. Alligator spring clips
Please Log In to view prices
Brush - Befaco, Gear Duster
Gear duster from Befaco. The Befaco Synth Duster is a great tool for getting dust off of faceplates and other hard to reach spots on your equipment. The super soft bristles can gently clean around pots, jacks, and other hardware.
Please Log In to view prices
String Action Gauge - Dunlop, System 65
The Dunlop System 65 String Action Gauge is a precision measurement tool for setups and adjustments. The gauge includes both metric and imperial measurements on opposite sides.
Please Log In to view prices
Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Please Log In to view prices
Fret Hammer - Twin Heads, for delicate work
Precision luthier hammer with wooden handle. Dual sided head has a steel end and a plastic end to allow for delicate work. Can be used for applications such as ensuring a proper fret fitting.
Please Log In to view prices
Storage Box - for electronic components
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.
Please Log In to view prices
Desoldering Pump - Manual, for removing solder
Handheld desoldering pump for solder removal. The enhanced dual spring-loaded piston creates a powerful vacuum for easy removal of molten solder. The static free tip is self cleaning and made from a clog resistant material. The aluminum body is lightweight and durable.
Please Log In to view prices
Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
Please Log In to view prices
ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
Please Log In to view prices
String Spreader - for fret work without unstringing
Package of 2
Those of us who don’t want to fully remove that new set of strings to do some quick spot work on the fret board or nut will love this simple yet effective tool. Simply loosen your strings and place the string spreaders underneath the guitar neck. Bring the strings off the neck and latch them underneath the spreader's ends to allow for quick and easy fret-board work without the need to unstring your instrument. These string spreaders will quickly become a must have in your toolbox!
  • Make room for cleaning, polishing or spot work on frets without removing strings
  • Made of brass with a soft, finish safe, rubber coating
Please Log In to view prices