You are here

Tools

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(2 pages)
S-T205Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2

Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.



Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret


Please Log In to
view prices
Click to read more
S-T237Fret Rocker - for Identifying Uneven Frets

Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.


Please Log In to
view prices
Click to read more
S-T206Fret Puller - Narrow Jaws, for removing frets

A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without fretboard damaging.


Please Log In to
view prices
Click to read more
S-T234String Spreader - for fret work without unstringing
Package of 2

Those of us who don’t want to fully remove that new set of strings to do some quick spot work on the fret board or nut will love this simple yet effective tool. Simply loosen your strings and place the string spreaders underneath the guitar neck. Bring the strings off the neck and latch them underneath the spreader's ends to allow for quick and easy fret-board work without the need to unstring your instrument. These string spreaders will quickly become a must have in your toolbox!



  • Make room for cleaning, polishing or spot work on frets without removing strings
  • Made of brass with a soft, finish safe, rubber coating

Please Log In to
view prices
Click to read more
S-T228XFret Polishing Rubber - Erases Fine Scratches & Marks
Package of 2

Make your frets shine with this fret polishing rubber. Erases fine scratches and marks. Set of 2. Because of the softness of the rubber, the polisher fits to fret arch perfectly and keeps the fingerboard damage to a minimum. Easy to cut for delicate fret work. This is a great rust remover and polisher!



Available in 1000 (tan), 400 (red), or 180 (blue) grit.


Please Log In to
view prices
Click to read more
S-T257Fret Bender - for creating radius in or flattening Fret Wire

Multi-functional Fret Bender - bend or staighten either bulk fretwire or pre-cut short piece fret wire precisely and quickly! For bending fret wire, crank a length of fretwire through the fret bender, and it comes out curved and ready to install in a radiused fretboard. Get a perfect bend on enough wire for a whole guitar in just seconds. Precisely radiused fretwire makes your fretwork fast, accurate, and professional.



Can be mounted to a workbench by using the two 5/16” bolt holes.


Please Log In to
view prices
Click to read more
S-T261Fret Press Inserts - for Pressing Frets, Multiple Radiuses

Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.


Please Log In to
view prices
Click to read more
S-T260Fret Press Caul - Converts Drill Press to Fret Press

Fret press caul. Perfect for converting your drill press or arbor press into a fret press. 3/8” shank. (Includes 2.5 mm hex key).



Used with radius inserts (S-T261) to press frets into guitar fret boards.


Please Log In to
view prices
Click to read more
S-T266Fret Setter - 10 cm Length
The contact surface of this solid brass tool fits over the crown of a fret and reseats loose fret ends without unstringing the instrument. Place the end of the tool on the crown of the fret and tap with a hammer.
Also works well for pressing loose fret ends down while supergluing.
Please Log In to
view prices
Click to read more
S-T262Fret Slotting Miter Box - for guiding fret saws

Use this Fret Slotting Miter Box to accurately cut fret slots with a fretting handsaw. The ball-bearing guides make sawing easier and faster; they hold your fret saw perpendicular to the fingerboard and can be adjusted to match the blade precisely. You can quickly slot any board up to 3"" (76.2mm) wide, with adjustable depth of cut for any fret wire. You always have an unobstructed view of your work.



Made of rugged aluminum and 12" (304.8mm) long, this miter box has convenient mounting holes for firm attachment to your workbench, the mounting screws and spanners are included. Instructions also included.


Please Log In to
view prices
Click to read more

Pages

(2 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Tools