Tools

Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
Please Log In to view prices
Solder wick - GC Braid, multiple sizes
5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.
Please Log In to view prices
Tolex Glue - Brush-on adhesive for applying tolex
Brush-on adhesive ideal for applying tolex. Cleans up with soap and water. No nasty solvents required. Does not stretch or shrink the vinyl. Comes in quarts or gallons. Specifications: Tolex Glue is a non-flammable, Neoprene based, water borne adhesive formulated to bond tolex and vinyl to wood and wood based substrates. Min. use temp: 45°F Freezes at 32°F and lower Shelf Life: 6 Months Directions: Surfaces to be bonded must be clean. Apply a very thin coat to both surfaces. Very porous surfaces may require more than one coat. Second coat should not be applied until first has dried. Allow to 'flash off' for 20-30 minutes. Cloudy areas indicate incomplete drying. This time can be shortened with forced air and/or heat. Position pieces carefully prior to bringing surfaces together as bond is made instantly.
Please Log In to view prices
Fret Puller - Narrow Jaws, for removing frets
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.
Please Log In to view prices
Solder - Kester, 60 / 40, 44 Flux, 1 lb spool
60/40 Rosin Core, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
Please Log In to view prices
Tool - Precision Devices, Lead Former, Various Sizes
High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.
Please Log In to view prices
Soldering Iron Tip - Weller, solid core, screwdriver type, ST Series
Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Please Log In to view prices
Nut File - Edge-Cut, for slotting guitar nuts
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4.5” cutting edge
  • Double sided (both sides are the same gauge)
  • 10 gauges available
  • Sold individually*
  • Made In Japan

*See S-T213-SET for a set of all 10 sizes.
Please Log In to view prices
Burnishing Tool - GC Electronics, ¼" wide, steel
Stainless steel strip, microscored to an ultrafine file surface. Remove oxide and corrosion on contacts made of platinum, paladium, moybdenum, gold, tungsten, and silver.
Commonly used to remove oxidation from electronic contact surfaces such as switches or connectors, restoring the connection and revitalizing the surface.
Please Log In to view prices
Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Package of 10
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
Please Log In to view prices
Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
Please Log In to view prices
Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
Please Log In to view prices
Soldering iron tip - Weller, solid core, conical, ST Series
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST7 - .031" / 0.79 mm diameter Conical tip
  • Tinned with Lead Free alloy
Please Log In to view prices
StripBoard - Single Sided, 3.15” x 1.97”, Mounting Holes
Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.
Please Log In to view prices
Solder - Kester, 60 / 40, 44 Flux, 66 Core, .031 Dia, .5 oz
Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz
Please Log In to view prices
Fret Rocker - for Identifying Uneven Frets
Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.
Please Log In to view prices
Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
Please Log In to view prices
Tip Cleaner - Wire Type for Soldering Irons
Coiled metal wire type tip cleaner for use with soldering irons. The metal wire cleaner requires no water which reduces temperature drops in the tip compared to using a sponge. The black metal holder is dome shaped to reduce airborne solder droplets when cleaning. The holder has a detachable top and bottom to easily empty when necessary.
Please Log In to view prices
Cutters - Xcelite, Shearcutter, General Purpose
5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:
  • Low profile, general-purpose cutter
  • Superior blade by-pass shear cutting action
  • Better cuts with half the effort
  • Greatly reduced mechanical shock delivered to the work
  • Features red grips
  • Flush cuts soft wire up to 20 AWG (0.8mm)
Please Log In to view prices
Standoffs - 0.18", plastic with adhesive backing
Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:
  • Low profile 0.180" standoff height.
  • Offset base allows use when holes are close to the PCB edge.
Please Log In to view prices
Nut Files - Double Edge, for guitars, 3 sizes
Package of 3
Double edge nut files featuring popular guitar gauges specially designed for slotting nuts. Each set of files is specifically designed for guitars of a particular type. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4” cutting edge
  • Set of 3 files
  • Made In Japan
Please Log In to view prices
Solder - Kester 63 / 37, 1 lb spool, 0.031" diameter
(63/37 Rosin Core) - ..031" Diameter, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
Please Log In to view prices
Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
Please Log In to view prices
Sandpaper - Kovax rolled, 1400 x 64 mm, Self-Adhesive
1.4m, Self adhesive type, 64mm width for S-T229-X sanding blocks.
Please Log In to view prices