Terminal Boards & Strips

Board - Marshall, Replacement for JCM 2000 DSL 100
Replacement board for Marshall JCM 2000 DSL 100
Please Log In to view prices
Eyelets - Brass, .121 x .125 x .200; MT .0095, package of 10
Package of 10
Eyelets, bag of 10 (mounts in 1/8" hole).
Please Log In to view prices
Eyelets - Plated Brass, Small, .089” x .125” x .150”
Package of 10
Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.
Please Log In to view prices
Fiberboard - Vulcanized, 3" x 15", .062" Thick
Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.
  • .062" thick
  • 3" x 15"
Please Log In to view prices
Kit - Fender® Stratocaster® Mid Boost Kit
Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.
Please Log In to view prices
PC Board - Dunlop, replacement for Crybaby
Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
Please Log In to view prices
PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
Please Log In to view prices
PCB - Marshall, Valve PCB TSL100 / TSL122, Rev 20
Marshall PC Board for TSL 100 / 122. Rev 20.
Please Log In to view prices
Solder Lug - #6 or #8 Hole, Locking
Package of 10
Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10
Please Log In to view prices
Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
Please Log In to view prices
Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
Please Log In to view prices
Tagboard - 300mm x 16mm, 26 Tags, single row
300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
Please Log In to view prices
Tagboard - 300mm x 56mm, 2 x 28 Tags
300mm x 56mm tagboard with two rows of 28 tags. Each connector features two lugs, one facing inward and one facing outward. This can be helpful when connecting components using the inner lugs which leaves the outside lugs open for wiring. A center row of holes can be used for running wires beneath the board as well as for standoffs.
Please Log In to view prices
Tagboard - 40 Turret Pins, High Quality
200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
Please Log In to view prices
Terminal Board - one 8 Pin socket, 2 x 6 lugs
Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
Please Log In to view prices
Terminal Board - one 9 Pin socket, 3 x 6 lugs
Single socket. 3 rows/6 lugs per row, 6 mounting holes. Board dimensions 3 ¾" x 3". Terminals are not pre-wired.
Please Log In to view prices
Terminal Board - two 8 Pin sockets, 2 x 12 lugs
Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
Please Log In to view prices
Terminal Board - two 9 Pin sockets, 2 x 12 lugs
Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
Please Log In to view prices
Terminal Board - two 9 Pin sockets, 3 x 10 lugs
Dual socket. 3 rows/10 lugs per row, 4 mounting holes. Board dimensions 5 ½" x 3 ¾". Terminals are not pre-wired.
Please Log In to view prices
Terminal Board - two 9 Pin sockets, for Dynaco Mark III
For Dynaco Mark III. Dual socket, 2 rows/11 lugs per row, 4 mounting holes. Board dimension 4.25" x 3.45". 0.125" thickness.
Please Log In to view prices
Terminal Strip - 1 row, 12 turrets per row
1 row/12 lugs per row. 2 mounting holes. Board dimensions 5 ¼" x ½".
Please Log In to view prices
Terminal Strip - 1 row, 6 turrets per row
1 row/6 lugs per row, 2 mounting holes. Board dimensions 3" x ½".
Please Log In to view prices
Terminal Strip - 2 Lug, 2nd Lug Common, Horizontal
Package of 5
Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.
Please Log In to view prices
Terminal Strip - 2 rows, 12 turrets per row
2 rows/12 lugs per row, 2 mounting holes, 5 ¼" x 1 ¼" board dimensions.
Please Log In to view prices