Terminal Boards & Strips

Shatterbox style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Shatterbox pedal. The board is styled after the later version with a printed circuit rather than a stripboard construction. This is the same board that was used in the “split board” version which can be built by cutting the board down the middle to separate the fuzz section from the treble booster section. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws.

Staking tool for small eyelets such as S-HEYE-B. Directions:

• Drill hole using #42 drill bit
• Insert eyelet
• Flip board over onto a hard service
• Center staking tool over the eyelet
• Strike staking tool with hammer to clamp eyelet to board

Premium versions of the pseudo eyelet boards with 7.5mm spacing. The premium versions feature 2.4mm thick boards with gold plated contacts. These PCBs have similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. For standard versions, see P-HTB-X. 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 7.5mm x 26mm eyelet spacing
• 57.15mm x 30.66mm board
• 45mm spacing for 3.2mm mounting holes
• Great fit for 125B and 1590N1 enclosures

2x12 Board:

• 2 rows of 12 eyelets (24 total)
• 7.5mm x 26mm eyelet spacing
• 87.15mm x 30.66mm board
• 75mm spacing for 3.2mm mounting holes
• Great fit for 1590BB enclosures

Turret board with pre installed turrets designed to be used to build a 5F6A layout or variants. Includes the required 2 pieces

• 2mm board
• 5F6A Layout
• Includes 2 pieces

Uninsulated fork terminals for use with #8 studs. These terminals fit 22AWG through 16AWG wire gauges and feature a serrated barrel for a strong crimped connection. Made of tin plated copper.

Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.

FZ-1 fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Maestro FZ-1 pedals. The board is styled after the original version that can also be found in early serial Maestro FZ-1A pedals. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets (sold separately). The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Phenolic PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The spacing between pads is 9.1mm horizontally and 34.4mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for 7.5mm spacing 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 9.1mm x 34.4mm eyelet spacing
• 69.42mm x 40.1mm board
• 54.6mm spacing for 3.2mm mounting holes
• Great fit for 1590P1, Gorva S90, and YY slanted enclosures

Turret strip, with 9 turrets. Measures 95mm x 15.875mm.