You are here

Switches

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(12 pages)
S-HM100-ASwitch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:

    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc.

Please Log In to
view prices
Click to read more
S-W603Wire - 4 Conductor, Shield
Shielded 4-conductor wire used in wiring pickups, controls etc. Shielded 4-conductor wire is commonly used in humbucking pickups to allow more wiring flexibility over the 2-conductor setup. Building a pickup using 4-conductor wire will allow you to wire up coil cut, phase switching, and series/parallel configurations. Additionally, 2 conductor pickups can be converted to 4-conductor using this wire.

  • Sold per foot
  • 28 AWG
  • Foil shield
  • 12”/3.2mm outer diameter
  • Sold individually
Please Log In to
view prices
Click to read more
S-W600-WWire - Push Back Cloth for Single Coil Pickup, White

White vintage style push back wire for building or repairing single coil pickups.Push back style eliminates the need for stripping.



  • Outer diameter: 0.07"
  • Sold by the foot

Please Log In to
view prices
Click to read more
W-SC-W056Nut - Replacement For Switchcraft, Deep Thread, Knurled for Switches
Colors Available:

Deep thread nut for use with Switchcraft switches. Used on some models of Gibson® guitars and other brands where the threading of the switch isn’t able to protrude through the body enough. Switchcraft toggles come stock with a flat washer and thicker bodied guitars with carved tops or Les Paul guitars with a selector ring require a nut with longer reach. These nuts will attach your switch to the nut through the body with no issues.



  • Fits genuine Switchcraft switches
  • Available in gold or nickel finish
  • Sold individually

Please Log In to
view prices
Click to read more
P-H514Switch - Fender®, Toggle, SPST, Standby, Solder Lugs

Original Fender®, Carling SPST power for Fender tube amps - 3A, 250VAC; 6A, 125VAC, ½" mounting hole.


Please Log In to
view prices
Click to read more
P-H390Switch - Rotary, 1 Pole, 12 Positions, ¼" Shaft, MBB

.3A 125 VAC. 1 pole, 12 position, solid ¼" shaft. Make before break (shorting).


Please Log In to
view prices
Click to read more
P-H391Switch - Rotary, 1 Pole, 12 Positions, ¼" Shaft, BBM

.3A 125VAC. 1 pole, 12 position, solid ¼" shaft. Break before make (non-shorting).


Please Log In to
view prices
Click to read more
P-H515Switch - Fender®, Toggle, SPST, Standby, Tabs

Original Fender®, Carling SPST standby for Fender tube amps - 3A, 250VAC; 6A, 125VAC.


Please Log In to
view prices
Click to read more
P-SW60Switch - Pickup Selector, Tele, 3-Way, Black

3-way pickup selector switch for Teles, black tip.


Please Log In to
view prices
Click to read more
P-SW61Switch - Pickup Selector, Strat, 5-Way, Black

5-way switch for Strats, black tip.


Please Log In to
view prices
Click to read more

Pages

(12 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Switches