Switches

Carling mini-toggle switch, DPDT, 2 position, ¼" mounting hole diameter, 0.354" bushing length.

Premium two position SPDT submini toggle switches from Gorva Design. The Bascular Sub Mini switches have a medium 7.37mm actuator length. These switches feature silver plated copper alloy contacts. The bushing is smooth and the switch is secured with the mounting bracket on the PCB. RoHS compliant & lead-free. Details

• 5.59mm non-threaded bushing
• 2-Position On/On
• 4.95mm panel hole diameter
• Single pole/Double throw (SPDT)
• PC Pins

Features

• Power Rating: DC9V, 1A
• Contact Resistance: <20mΩ
• Insulation Resistance: 1000MΩ Minimum
• Dielectric Strength: 1000V RMS @ Sea Level
• Operating Temperature: -40°C ~ +85°C
• Electrical Life: 30,000 Cycles
• RoHS & Lead-free

Low profile switches with a smaller footprint than the standard 3PDT sizes. These footswitches are perfect for cramped layouts but are also great for general use. The small solder lugs are great for wiring by hand that also work well with PCB layouts. Mounting hardware included. Features

• Latching Footswitch
• 3PDT
• Low Profile
• Small Solder Lugs
• Hardware Included

Switchcraft 3 position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® PSTS-010. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. This version of the L-Type switch is used in the common two pickup wiring for a neck position, middle position with neck and bridge, and a bridge position.

Switchcraft 3 position Pickup Selector, Replacement for Gibson Straight-Type. As found on LP style solid body guitars.

Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.406” center-to-center mounting hole spacing
• #4-40 screws recommended for mounting
• Screws not included

Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs

• DPDT ( Double Pole/ Double Throw) switch
• 0.354" bushing length
• 0.409” bat length
• ¼" chassis hole diameter
• Solder terminals

High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.

Carling SPST latching On-Off footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).

Oak® single wafer 5 way lever switch.Standard U.S. size. Fits 1/16" x 1-1/16" slot. 1-5/8" center to center screw spacing. 1-3/8" cavity depth. The importance of the “right” feel required by guitarists has resulted in a continually designed and developed lever switch, providing a superior product. For over three decades, these lever switches have been tested and refined to meet the needs and desires of guitar players all over the world. Patented “T” slugs secure solder-lug clips to the stator. Mounting screws included.

Carling, SPST 2 position toggle switch, On-Off. 10A 250VAC, 15A 125VAC. Made in Mexico. Note: On-Off switches may sometimes be referred to as On-None-Off.

Good latching stomp-box effects switch (Double Pole, Double Throw), On-On. Solder Lugs. 1A 250V, 3A 125V Note: On-On switches may sometimes be referred to as On-None-On.

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

3 pole, 4 position (make before break) rotary switch with a ¼" solid shaft. 3P4T rotary switch.

Premium three position DPDT mini toggle switches from Gorva Design. The Bascular Mini switches have a medium 7.5mm actuator length. These switches feature silver plated copper contacts. RoHS compliant & lead-free. Mounting hardware included. Details

• 8.89 mm bushing length
• Medium bat
• 3-Position On/On/On
• ¼" mounting hole diameter
• Double pole/Double throw (DPDT)
• Solder lugs

Features:

• Power Rating: DC9V, 1A
• Contact Resistance: <10mΩ
• Insulation Resistance: 1000MΩ Minimum
• Dielectric Strength: 1000V RMS @ Sea Level
• Operating Temperature: -40°C ~ +85°C
• Electrical Life: 40,000 Cycles
• RoHS & Lead-free

0.354" bushing length. 2-Position On/On. ¼" mounting hole diameter. Double pole/Double throw (DPDT). PC mount pins.

Latching DPDT footswitch, PC mount. Made in Taiwan.

3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.

Carling mini-toggle switch, SPDT, PC Pins. 2-Position.

• 0.354" bushing length
• 2-Position On/On
• ¼" mounting hole diameter
• Single pole/Double throw (SPDT)
• PC mount pins

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 3 position switch with knob and mounting hardware.

Carling, DPST toggle, 2-position, On-Off with solder lugs (3A, 125V), .500"" toggle length, 0.465" bushing length. Note: On-Off switches may sometimes be referred to as On-None-Off.

Carling, DPDT latching footswitch, On-On, with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.

Carling, DPDT 2 position toggle with solder lugs (6A, 125V). 0.687" toggle length. On-On.
Note: On-On switches may sometimes be referred to as On-None-On.

Lighted DPST On-Off power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.