You are here

Semiconductors

Filter these results
Sort By:
products per page
View Mode: List View · Grid View
P-QSJE5332Transistor - Peavey, SJE 5332, 120V, 3A

SJE 5332, 120V, 3A, Case-77.


Please Log In to
view prices
Click to read more
P-Q2N3904Transistor - 2N3904, TO-92 case, NPN

General purpose low-power NPN bipolar junction transistor, used frequently in hobbyist electronic projects.


Please Log In to
view prices
Click to read more
P-QTL074Op-Amp - TL074, Quad, Low-Noise, JFET Input, 14-Pin DIP

Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:



  • Wide common-mode and differential voltage range
  • Low input bias and offset current
  • Low noise en = 15 nV/HZ
  • Output short-circuit protection
  • High input impedance JFET input stage
  • Low harmonic distortion: 0.01%
  • Internal frequency compensation
  • Latch up free operation
  • High slew rate: 16 V/us (typical)

Please Log In to
view prices
Click to read more
P-QTDA7293Integrated Circuit - Marshall, TDA7293 amplifier

120V - 100W DMOS audio amplifier with mute/standby. The TDA7293 is a monolithic integrated circuit in Multiwatt15 package, intended for use as audio class AB amplifier in Hi-Fi field applications, such as home stereo, self powered loudspeakers and Topclass TV. Thanks to the wide voltage range and to the high output current capability it is able to supply the highest power into both 4-Ω and 8-Ω loads.


Please Log In to
view prices
Click to read more
P-QLM386N1Audio Power Amplifier - LM386N-1, Low Voltage

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.


Please Log In to
view prices
Click to read more
P-Q1N400XDiode - General purpose rectifier, 1A, 1N400X

A semiconductor device which passes current in the forward direction (from anode to cathode), and blocks current in the opposite direction.


Please Log In to
view prices
Click to read more
P-QTL082Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP

Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.


Please Log In to
view prices
Click to read more
P-Q2N3055Transistor - 2N3055, High Power NPN Silicon, TO-3 Case
15 A, 60 V, 115 W
EPIBASE - Designed for power amplifier and switching regulator applications. The best choice where high frequency response, low switching losses and good safe operating area are required.
  • Current Gain - Bandwidth Product - fT = 2.5 MHz (Min) @ Ic = 1.0 Adc
  • Safe Operating Area - Full Power Rating to 40 V
Please Log In to
view prices
Click to read more
P-QBA4560Op-Amp - BA4560, Dual, General Purpose, 8-Pin DIP

The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.


Please Log In to
view prices
Click to read more
P-QLM741Op-Amp - LM741, Single, general purpose, 8-Pin DIP

LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.



The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.


Please Log In to
view prices
Click to read more
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Semiconductors