Radio & Antique Equipment Parts
Motor Assembly - Lower Slow, for Leslie 122/147
Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
Motor Assembly - Upper Slow, for Leslie 122/147
Replacement upper slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
- Primary: 4000 turns, #41 wire (lugs 4 & 2)
- Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
- Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
- Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
- Lamination Core Size: 5/8" x 1/2"
- Weight: 7 oz.
Grommet Kit - All Rubber Parts, for Leslie
Package of 33Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.
Vibrator - 12 Volt, 3 Pin, Negative Ground
New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Vibrator - 4 Pin, for automobile radio
New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Relay - 115 Volt AC, for Leslie 147
Replacement relay for Leslie model 147 amplifier, 115 VAC , SPDT. The contacts are rated at 10A.
Wire - 18 Gauge, 2 conductor, braided Power Cord
Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.
Relay - SPDT, Leslie 122 Retrofit
Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil.
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Coil EMC suppression
- Cadmium Free contact material
Switch - for Run Circuit in Hammond Organ
Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
Socket - Leslie, 6 Pin Female, wavy washer
6 pin female socket with wavy washer, for Leslies.
Power Supply - Power All System, For Effects Pedals
The Power-All PA-9 Digital Power Supply is the world’s first 2,000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2,000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
Vibrapod Isolator - Isolate Components
Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane.
Belt - Leslie, 31", Lower Drive, for 122/147
Replacement lower drive belt, white, 31" circumference.
Electroplating Compound - for metal coating
Uses current from any 3 to 6 volt D.C. supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Brush not included. Available in multiple materials.
Alignment Kit - GC Electronics, for CB
Package of 8Contains
- 5009 Duplex no-metal screwdriver
- 5097 K-tran tool
- 8271 core aligner
- 8282 Zenith alignment tool
- 9091 hex iron core tool
- 9440 transistor tool
- 8276 Duplex aligner
- 9304 double end tool
Rotor Cover - 17", for Leslie 122/147
17" rotor cover fits Leslie models 122/147.
Power Supply - Power All System, 9V, 2000mA, for Effects Pedals
The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
Coil - Miniature adjustable coil, 70, oscillator
Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.
Belt - Leslie, 31", Lower Drive, for 122/147, Polyurethane
Replacement lower drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 31 in. diameter with a sanded seam to ensure a smooth drive.
Plug - for Leslie, 6 Pin Male, wavy washer
6 pin male plug with wavy washer, for Leslies.
Belt - Leslie, Upper Drive, 25.5", for 122/147, Polyurethane
Replacement upper drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 25.5 in. diameter with a sanded seam to ensure a smooth drive.
Plug Cover Kit - Leslie, for Connectors
Plug cover kit for Leslie , screws included. This is the connector cap for the connecting cable.
Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
- Voltage: 9VDC
- Current: 200mA
- Tip positive; Sleeve negative