Radio & Antique Equipment Parts

Screw Set - Leslie, Back Panel, 13 Phillips Screws, Washers
Set of 13 phillips head screws for Leslies. Includes 13 flat washers. 13 pieces replaces all of the screws on the upper cover, lower cover and middle back panel.
package of 13
Please Log In to view prices
Vibrator - 12 Volt, 3 Pin, Negative Ground
New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Please Log In to view prices
Cable - Power All, 11 Lead Right Angle Daisy Chain
Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.
Please Log In to view prices
Plastic Polish - Novus #3, heavy scratch remover
Removes scratches from acrylic surfaces; significantly reduces haziness. More abrasive than Novus #2 and is effective for deeper scratches. Treatment should be followed by Novus #2 to buff and polish surface.
Please Log In to view prices
Bearing - Leslie, Upper Tension Idler
Sealed upper tension idler bearing for Leslies
Please Log In to view prices
Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
  • Primary: 4000 turns, #41 wire (lugs 4 & 2)
  • Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
  • Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
  • Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
  • Lamination Core Size: 5/8" x 1/2"
  • Weight: 7 oz.
Please Log In to view prices
Aligner tool - GC Electronics, Duplex
Butyrate shaft 6-1/8" long with 1/8" wide steel tips. Tip on one end recessed.
  • Material: Conductive Nylon Metal
  • End: 1/8"
  • End 2: 1/8"
Please Log In to view prices
Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive
Please Log In to view prices
Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
Please Log In to view prices
Nut - Wire nut, Small size for 16 - 18 gauge wire
Small wire nuts, for use on appliances, televisions, stereos, antennas, or for any small wiring application.
package of 12
Please Log In to view prices
Cable - Power All, Green Right Angle Line-6 Extension Jumper
Included in the PA-9ECB Basic Kit, PA-9ECD Deluxe Kit, and also available separately, the Cable-Green Right Angle jumper allows the user to power Line-6 Stomp-Box modelers and other digital effect units from the ECO-Dapter®. The Cable-Green features a reverse-polarity (tip positive), right-angle male barrel connector with a larger, 2.5 mm internal diameter and spring-loaded clips. The Cable-Green/R can be used with Line-6 Modelers, Electro-Harmonix units, and other pedals requiring a larger internal diameter plug. the Cable-Green/R can be connected to the male plugs on any Power-All Daisy Chain, or directly to the ECO-Dapter® itself.
Please Log In to view prices
Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
Please Log In to view prices
Relay - SPDT, Leslie 147 Retrofit
Reliable replacement relay for the Leslie 147. The small size makes this high quality relay easy to retrofit in the 147. Its performance exceeds the original relays used in the Leslie 147 with its very low switching noise and high ratings on both the contacts and the coil. Features:
  • 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
  • Coil EMC suppression
  • Cadmium Free contact material
Please Log In to view prices
Switch - for Run Circuit in Hammond Organ
Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
Please Log In to view prices