Radio & Antique Equipment Parts

Motor Assembly - Upper Slow, for Leslie 122/147
Replacement upper slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
Please Log In to view prices
Motor Assembly - Lower Slow, for Leslie 122/147
Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
Please Log In to view prices
Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
Please Log In to view prices
Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
  • Primary: 4000 turns, #41 wire (lugs 4 & 2)
  • Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
  • Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
  • Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
  • Lamination Core Size: 5/8" x 1/2"
  • Weight: 7 oz.
Please Log In to view prices
Grommet Kit - All Rubber Parts, for Leslie
Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.
package of 33
Please Log In to view prices
Vibrator - 4 Pin, for automobile radio
New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Please Log In to view prices
Vibrator - 12 Volt, 3 Pin, Negative Ground
New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Please Log In to view prices
Relay - SPDT, Leslie 147 Retrofit
Reliable replacement relay for the Leslie 147. The small size makes this high quality relay easy to retrofit in the 147. Its performance exceeds the original relays used in the Leslie 147 with its very low switching noise and high ratings on both the contacts and the coil. Features:
  • 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
  • Coil EMC suppression
  • Cadmium Free contact material
Please Log In to view prices
Socket - Leslie, 6 Pin Female, wavy washer
6 pin female socket with wavy washer, for Leslies.
Please Log In to view prices
Switch - for Run Circuit in Hammond Organ
Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
Please Log In to view prices
Power Supply - Power-All® ECO-Dapter®, Cable Kits, for Effects Pedals
Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.
Please Log In to view prices
Relay - SPDT, Leslie 122 Retrofit
Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil. Features:
  • 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
  • Coil EMC suppression
Please Log In to view prices
Wire - 18 Gauge, 2 conductor, braided Power Cord
Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.
Please Log In to view prices
Alignment Kit - GC Electronics, for CB
Contains
  • 5009 Duplex no-metal screwdriver
  • 5097 K-tran tool
  • 8271 core aligner
  • 8282 Zenith alignment tool
  • 9091 hex iron core tool
  • 9440 transistor tool
  • 8276 Duplex aligner
  • 9304 double end tool
package of 8
Please Log In to view prices
Rotor Cover - 17", for Leslie 122/147
17" diameter rotor cover fits Leslie models 122/147. 13" in height. Replace torn or missing rotor covers.
Please Log In to view prices
Power Supply - Power-All® ECO-Dapter®, 9V, 2000mA, for Effects Pedals
Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects.
Please Log In to view prices
Plug - for Leslie, 6 Pin Male, wavy washer
6 pin male plug with wavy washer, for Leslies.
Please Log In to view prices
Belt - Leslie, 31", Lower Drive, for 122/147, Polyurethane
Replacement lower drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 31 in. diameter with a sanded seam to ensure a smooth drive.
Please Log In to view prices
Cement - GC Electronics, Service Cement
A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.
Please Log In to view prices
Plug Cover Kit - Leslie, for Connectors
Plug cover kit for Leslie , screws included. This is the connector cap for the connecting cable.
Please Log In to view prices
Bearing - Leslie, Lower Rotor, sealed
Sealed lower rotor bearing for Leslies.
Please Log In to view prices
Belt - Leslie, Upper Drive, 25.5", for 122/147, Rubber
Replacement upper drive belt for Leslie models 122 and 147. This belt is made of a high quality rubber that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 25.5 in. diameter with no seam to ensure a smooth drive.
Please Log In to view prices
Spring - Leslie, Tension, for Upper Belt
Replacement upper belt tension spring for Leslies.
Please Log In to view prices
Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
Please Log In to view prices