Rocket Sockets by Pepers' Pedals allow for the tightening of various nuts for jacks, potentiometers and switches on guitar effects pedals without scratching the enclosure and damaging the graphics or paint as the typical metal tools will do.

Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.

Simple and easy to use nut driving tool for the slotted nuts found on Qingpu jacks that are commonly used in Eurorack modules. The tool anchors into the sleeve of the jack ensuring no slippage when in use, protecting the faceplate from accidental damage. The two grip holes are cut to the size of M2.5 and M3 hex nuts and can be used in a pinch to tighten nuts of those sizes, or to hang your tool on a keyring! One side of the tool works with Mod "Top Brass" nuts and slotted W-QP-NUT-K nuts used on W-QP-518MA, W-QP-419GR, and W-QP-518MA-BM. The other side works with slotted W-QP-NUT-PJ-R nuts used on W-QP-PJ3410. Either side will work with Befaco Bananuts for 3.5mm jacks (W-BNUT-X). The nut driving tool is made of steel.

5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:

• Low profile, general-purpose cutter
• Superior blade by-pass shear cutting action
• Better cuts with half the effort
• Greatly reduced mechanical shock delivered to the work
• Features red grips
• Flush cuts soft wire up to 20 AWG (0.8mm)

High quality Phillips head truss rod wrench. This Japanese made wrench is the perfect tool for cross slotted truss rod nuts found on many Fender® necks. The compact 9mm diameter head has a thin 11mm width allowing for adjustments without removing the neck

Instructions

• Simply drill 3/8" hole insert cutting head and compress handles.
• Gives you the ability to make square holes for fuse holders, special connectors displays etc.

1. Material to be nibbled is placed in the gap between the punch and blade channel.
2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
3. A scribe line can be followed by looking down on work in this position.

Turret staking tool for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:

• Drill 1/8" hole
• Insert eyelet
• Flip board over on to a hard service
• Center staking tool over the eyelet
• Strike staking tool with hammer to clamp eyelet to board

Bourns trimmer adjustment tool. This tool is compatible with both the R-VT96Y-X multiturn trimmers and the R-VT62P-X single turn trimmers. The recessed end is especially helpful when used with the 3296Y trimmers to avoid slipping off of the screw adjuster. Features

• Meets UL 94V-0
• Pocket clip
• For use on most trimmer shafts/rotors
• Recessed end for use with extended shafts
• RoHS compliant

Instrument and amp jacks are notorious for coming loose. And with a shallow nut and recessed cavity, access can be challenging. Until now, that is. The GrooveTech Jack and Pot Wrench provides three thin-wall sockets - ½", 7/16", and 12mm - in a compact four-inch tool to handle the most common sizes of jacks and pots on instruments, amps, and other audio gear. Add a dab of threadlocker, and you'll probably never have to deal with that loose jack again. Sockets are pro-grade with a dazzling polished chrome finish.

Gear duster from Befaco. The Befaco Synth Duster is a great tool for getting dust off of faceplates and other hard to reach spots on your equipment. The super soft bristles can gently clean around pots, jacks, and other hardware.

Adhesive backed standoff with M3 threading. The high-strength adhesive tape allows the standoff to be securely mounted, providing an easy option for mounting PCBs in enclosures. These standoffs use a captive metal nut in a strong nylon plastic base for a durable and lightweight solution.

Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.

5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.

Resealable anti-static bags with a zip top. These pink reusable bags are made of polyethylene and are ideal for storing static sensitive electronic parts such as transistors, JFETs, ICs, CMOS, etc. The zip top uses a heavy duty double-track zipper.

Brush-on adhesive ideal for applying tolex. Cleans up with soap and water. No nasty solvents required. Does not stretch or shrink the vinyl. Comes in quarts or gallons. Specifications: Tolex Glue is a non-flammable, Neoprene based, water borne adhesive formulated to bond tolex and vinyl to wood and wood based substrates. Min. use temp: 45°F Freezes at 32°F and lower Shelf Life: 6 Months Directions: Surfaces to be bonded must be clean. Apply a very thin coat to both surfaces. Very porous surfaces may require more than one coat. Second coat should not be applied until first has dried. Allow to 'flash off' for 20-30 minutes. Cloudy areas indicate incomplete drying. This time can be shortened with forced air and/or heat. Position pieces carefully prior to bringing surfaces together as bond is made instantly.

Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:

• Low profile 0.180" standoff height.
• Offset base allows use when holes are close to the PCB edge.

Stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated strips
• 20 x 10 holes (10 strips)
• 3.04” x 1.55”

Stripboard featuring standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated strips
• 30 x 15 holes (15 strips)
• 3.04” x 1.55”

Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green