Power Supplies & Accessories

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut
Please Log In to view prices

Package of 5
The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201. Please Log In to view prices

Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Please Log In to view prices

High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
Please Log In to view prices

Colors Available:
Please Log In to view prices

18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.
Please Log In to view prices

Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Please Log In to view prices

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
Please Log In to view prices

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
- Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
- Securely anchors, insulates, and protects cables at panel entry points
Please Log In to view prices

Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5 Please Log In to view prices

Package of 5
Listed diameter is inside diameter. Sold in packs of 5.- 3/8" diameter designed for chassis hole with diameter 1/2"
- 1/8" diameter designed for chassis hole with diameter 1/4"
- 3/16" diameter designed for chassis hole with diameter 5/16"
- 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
- 1/4" diameter designed for chassis hole with diameter 7/16"
- 5/16" diameter designed for chassis hole with diameter 7/16"
Please Log In to view prices

Power Cord / cable - (3 conductor) Bare End, 16 AWG
Please Log In to view prices

Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Please Log In to view prices

Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. SKU Diameter P-HCABLECLAMP-38 ⅜ in. P-HCABLECLAMP-12 ½ in.
Please Log In to view prices

Nylon cable clamp with room for 1/4” cable outer diameter. Perfect for securing cables to cabinet walls. For larger ½” cable clamps see P-HCABLECLAMP-10.
Please Log In to view prices

Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
Please Log In to view prices

Package of 4
Mount these rubber grommets to the base of reverb tanks to help alleviate feedback and other vibration issues. The thick rubber ring helps with isolating the tank from the surface that it is mounted to or resting upon. These rubber grommets fit typical reverbs tanks. Mounting Hole Diameter = 3/8" Outer Diameter = 1/2". Package of 4. Please Log In to view prices

Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
Please Log In to view prices

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
Please Log In to view prices

Package of 5
Protect your expensive investment or hobby with inexpensive fuses. Please Log In to view prices

½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
Please Log In to view prices

Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
Please Log In to view prices

1/16” (.062 in.) panel thickness version of the Fender® style strain relief for 35/64" x ⅝” chassis holes and 11/32” cord diameter. Fits many Fender® amps with 1/16” thick chassis.
- Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
- Securely anchors, insulates, and protects cables at panel entry points
Please Log In to view prices

High quality chassis mount battery holder. This steel holder fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited.
Please Log In to view prices