Power Supplies & Accessories

Fuse kit, fast and slow blow. Contains the following fuses:

• 20x Slo-Blo, 2 Amp F-Z3AG-S2
• 20x Slo-Blo, 3 Amp F-Z3AG-S3
• 20x Slo-Blo, 1 Amp F-Z3AG-S1
• 20x Slo-Blo, 4 Amp F-Z3AG-S4
• 20x Slo-Blo, 5 Amp F-Z3AG-S5
• 20x Fast-Blo, 2.5 Amp F-Z3AG-F2D5
• 20x Fast-Blo, 1 Amp F-Z3AG-F1
• 20x Fast-Blo, 3 Amp F-Z3AG-F3

Protect your expensive investment or hobby with inexpensive fuses.

The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.

Protect your expensive investment or hobby with inexpensive fuses. • GMA Type • Measures .78"(20mm) in length, 0.19"(5mm) in diameter • Fast-Blow • Package of 5

Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5

The Power Plug 6 / 12 attenuator is a "must have" device for anyone that plays a tube amp. If you want to work your power tubes without ear-splitting volume, you need an attenuator. The Power Plug is the BEST attenuator made for amps 50 watts and less. Simple 2 switch operation for -6db or -12db attenuation. Get your best tone!
Why 6/12? Engage 1 switch and remove -6db of power. Engage the 2nd switch and you're -12db. That's a volume reduction of 60%. The Recycled Sound attenuator is a passive, resistive load with compensated impedance and EQ, which maintains the designated impedance, EQ'd such that no degradation in tone is noted, even at full -12db attenuation. Use it as a Master Volume, use it to save your hearing at practice, find your tube tone without getting thrown out of the club, use it to prevent blowing up your vintage or low power speakers.
Use TWO in series and achieve -24db attenuation - bedroom level!

KA-193 wallwart power supply. For use with PX4, PX4B and PXR4.

• Voltage: 4.5VDC
• Current: 500mA
• Tip positive; Sleeve negative

For use with MS2000, microKONTROL, microKORG, Etribes, DT7, AX1G/B, AX100G, AX1500, GT12, OT12, and PX3/3B.

Korg KA-163E / YP-055 power supply. For use with AM8000R, D8, D12, D16, DL8000R, KARMA, KM2, N1, N1R, N5, N5EX, SP500, TR Series, Triton LE

• Voltage: 9VAC
• Current: 3000mA
• 4 pin connector

Korg Power Supply, KA-310 adapter for X50, MicroX, R3, MR1000, or SP170. Please note that this requires an S-W128 AC power cord to connect to an AC wall outlet.

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the PA-9 Power-All to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices

Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.

Included in the Power-All System and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the PA-9 itself.

Included in the Power-All System and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a 1/8" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the PA-9 itself.

Included in the Power-All system and also sold separately, the Cable-Green Right Angle jumper allows the user to power Line-6 Stomp-Box modelers and other digital effect units from the PA-9. The Cable-Green features a reverse-polarity (tip positive), right-angle male barrel connector with a larger, 2.5 mm internal diameter and spring-loaded clips.

Included in the PA-9 Power-All System and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.

Included in the Power-All System and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.

Designed to fit over unused male barrel connectors on a daisy chain or power supply, Cable-Caps protect against short circuits that can occur when a live lead touches a metal surface. Sold in sets of three. Fits over standard 5.5 mm diameter barrel plug connectors.

The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.

The Power-All PA-9 Digital Power Supply is the world’s first 2,000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2,000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.

The Power Plug 100 offers the same -10db as the Power Plug Lite (M-PPLITE) but adds another "Bedroom Level" pot for further attenuation of up to -30dB AND is suitable for amps up to 100 watts! Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume. So you can adjust your amp as usual and use the attenuator as an overall Master volume.

The Power Plug Lite offers up to -10db attenuation in a rotary switch with -2db increments. The Power Plug Lite will accept all impedances and is rated for up to 50 watt amps. The same cool extruded aluminum case as the original Power Plug (M-ATT-6-12) for those who want a lighter touch and more control. Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume.

This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.

• Voltage: 9VDC
• Current: 200mA
• Tip positive; Sleeve negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

• Voltage: 9VDC
• Current: 200mA
• Tip Negative; Sleeve positive