Power Supplies & Accessories

Cable Tie Mount - Nylon, Adhesive Backing
Package of 5
Colors Available:
Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.
Please Log In to view prices
Cable Tie - Nylon, 5.5”, 18 lb
Package of 10
Colors Available:
Durable nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features
  • Approved for outdoor use.
  • UL Listed 6.6 nylon.
  • Locks tightly - Won’t stretch or slide.
  • Temperature range from 40° to 180°F.
Please Log In to view prices
Receptacle - IEC C14, Snap-in Panel Mount
High quality snap-in IEC C14 power entry connector. The connector is easy to install and is rated for 250VAC at 15A. The quick disconnect terminals can also be directly soldered to. Features:
  • High quality thermoplastic housing
  • Copper alloy terminals (4.8mm width)
  • Quick installation
  • Fits 0.8mm to 2mm thick panels
Please Log In to view prices
Receptacle - IEC C14, Bulgin, Replacement for Marshall Pignose
Black nylon AC power entry connector with the same mounting dimensions as the original Bulgin “Pignose” connectors used on early Marshall amps. This connector allows the amp to be fitted with a safer connector with no modifications to the chassis. Mounting hardware not included.
Please Log In to view prices
Dust Cap - For DC Power Jack, Low Profile Size
Dust cover for smaller low profile DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.
Please Log In to view prices
Dust Cap - For DC Power Jack, Standard Size
Dust cover for standard size DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.
Please Log In to view prices
Power Jack - DC Panel Mount, 5.5mm External, 2.1mm Internal
Colors Available:
New!:
½" panel mount with solder lugs. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
Please Log In to view prices
Cable - Battery to 2.1mm DC Plug, Center Negative
Cable for connecting 9V batteries to pedals via their DC input jack. This cable is great for using batteries with pedals that don’t have a battery compartment or for quickly switching from a power supply to a battery. This cable is 3 ¼” inches in length. The barrel plug has a 5.5mm outer diameter and 2.1mm inner diameter. Battery not included.
Please Log In to view prices
Power Jack - Lumberg, DC Panel Mount, Snap-in, 5.5mm External, 2.1mm Internal
Snap-in Lumberg panel mount barrel jack with solder lugs. This high quality jack is a similar size to the Lumberg low profile jack but easily snaps into place with no need to thread a nut inside the chassis. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter.
Please Log In to view prices
Fuse Holder - for Marshall, 3AG Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.
Please Log In to view prices
Fuse Holder - 3AG-Type, High Quality, Low Profile
High quality fuse holder used with 3AG type fuse. This fuse holder features a low profile design. This holder used 0.187” (4.8mm) quick connect tabs that can also be soldered to. Mounting nut included. 13.2mm hole required for mounting.
Please Log In to view prices
Power Jack - Cliff, DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
Please Log In to view prices
Insulation Cover - Fuse Holder, 15.5 x 36.8mm, PVC
High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
Features
  • Provides insulation against shock on rear of fuse holder
  • PVC
  • UL94V-0 rated flame retardant material

Fits S-H205
Please Log In to view prices
Cord - Power, 18 AWG, 3 Conductor, SVT, 6 ft, Gray
18AWG SVT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. SVT cords have a thinner insulation than SJT cords. This version comes in gray to pair with vintage style amps and equipment.
Please Log In to view prices
Power Jack - Lumberg, DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Please Log In to view prices
Cable Clamp - Nylon, .203” Mounting Hole
Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. SKU Diameter P-HCABLECLAMP-38 ⅜ in. P-HCABLECLAMP-12 ½ in.
Please Log In to view prices
Fuse Holder Cap - 3AG, Slotted, for Marshall 2000 Series
Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.
Please Log In to view prices
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, .062" Panel Thickness
1/16” (.062 in.) panel thickness version of the Fender® style strain relief for 35/64" x ⅝” chassis holes and 11/32” cord diameter. Fits many Fender® amps with 1/16” thick chassis.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
Please Log In to view prices
Strain Relief - Nylon, 0.3", 2 or 3 Conductor Wire
Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
Please Log In to view prices
Strain Relief - Nylon, 0.11" x 0.21" Wire (SPT-1)
Nylon strain relief for two conductor SPT-1 wire (.11" x .21”). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.375” x 0.345” mounting holes with 0.62” panel thickness.
Please Log In to view prices
Fuse Holder - 3AG-Type, Tweed Style, Solder Lug
Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Please Log In to view prices
Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
Please Log In to view prices
Fuse Block - For GMA / GMD Fuses, Low Profile
Open frame fuse block for GMA or GMD 5×20mm size fuses with a low profile design that features solder terminals made of tin plated brass. A unique design feature provides self-alignment of the clips to the fuse caps. This feature, plus a one-piece clip/terminal design, assures low contact resistance.
Please Log In to view prices
Fuse Holder - for Marshall, GMA or GMD Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.
Please Log In to view prices