Power Supplies & Accessories

Strain Relief - Nylon, 0.3", 2 or 3 Conductor Wire
Nylon strain relief for two or three conductor round wires ranging from 0.25” to 0.30” in diameter. Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.5” x 0.45” mounting holes with 0.62” panel thickness.
This is a direct fit for many vintage Fender amps with 2-prong cables, allowing for conversion to 3-prong SVT cables (such as S-W142) with the appropriate outer diameter.
Please Log In to view prices
Switch - Rotary, AC Power, In-line Cable Mount, SPT-1
Cable-mounted inline switch (On-Off) most often used for lamps and other applications. This switch pairs with SPT-1 type power cords and features a thumbwheel actuator.
Please Log In to view prices
Strain Relief - Rubber, for ¼" Diameter Hole
Strain relief for wiring - for use in 1/4 diameter hole.
Please Log In to view prices
Box Header - Shrouded, 10 Pin, Right Angle
High quality right angled 10-pin headers. Right angled headers are perfect for compact eurorack builds. The durable glass filled polyester shroud makes soldering these shrouded headers a simple task.
Please Log In to view prices
Power Jack - DC Panel Mount, Vintage Boss Style, 5.5mm External, 2.1mm Internal
This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.
Please Log In to view prices
Power Jack - DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
Please Log In to view prices
Power Jack - DC PC Mount, 5.5mm External, 2.1mm Internal
This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
Please Log In to view prices
Replacement Fuse Holder Cap - For P-SP2-500
Fuse holder cap replacement for P-SP2-500 power receptacle.
Please Log In to view prices
9V Battery Cushion - Vinyl Foam Tape, 3M, ½” x 2”
1/2 inch by 2 inch adhesive foam strip for cushioning 9V batteries in pedal enclosures. This black, medium density foam used an acrylic adhesive and paper liner. The high quality 3M materials ensure a durable foam and lasting adhesive. Made with ¼ inch thick foam.
Please Log In to view prices
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
Please Log In to view prices
Battery Clip - 9 Volt with Vinyl Tab
Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.
Please Log In to view prices
Strain Relief - Nylon, 0.11" x 0.21" Wire (SPT-1)
Nylon strain relief for two conductor SPT-1 wire (.11" x .21”). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points. Fits 0.375” x 0.345” mounting holes with 0.62” panel thickness.
Please Log In to view prices
Dust Cap - For DC Power Jack, Standard Size
Dust cover for standard size DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.
Please Log In to view prices
Cable Clamp - Black Nylon, .203” Mounting Hole
Black nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables. See P-HCABLECLAMP-X for white nylon versions of these clamps.
Please Log In to view prices
Dust Cap - For DC Power Jack, Low Profile Size
Dust cover for smaller low profile DC power jacks. This cover is simple to install and can help protect the power jack on effects pedals and other electronics using this style of DC jack. Jack sold separately.
Please Log In to view prices
Cable Clamp - Nylon, .203” Mounting Hole
Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables.
Please Log In to view prices
Fuse Holder - Clip, GMA-Type, PCB Mount
Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.
Please Log In to view prices