Power Supplies & Accessories

Attenuator - Recycled Sound, Power Plug 6 / 12, -6dB or -12dB
The Power Plug 6 / 12 attenuator is a "must have" device for anyone that plays a tube amp. If you want to work your power tubes without ear-splitting volume, you need an attenuator. The Power Plug is the BEST attenuator made for amps 50 watts and less. Simple 2 switch operation for -6db or -12db attenuation. Get your best tone!
Why 6/12? Engage 1 switch and remove -6db of power. Engage the 2nd switch and you're -12db. That's a volume reduction of 60%. The Recycled Sound attenuator is a passive, resistive load with compensated impedance and EQ, which maintains the designated impedance, EQ'd such that no degradation in tone is noted, even at full -12db attenuation. Use it as a Master Volume, use it to save your hearing at practice, find your tube tone without getting thrown out of the club, use it to prevent blowing up your vintage or low power speakers.
Use TWO in series and achieve -24db attenuation - bedroom level!
Please Log In to view prices
Cord - Power, for United Kingdom plugs, 8 feet
Detachable 3 conductor power cord for United Kingdom wall outlets. Cord end is IEC connected. GTSA-3 (Marshall™ type) 18 AWG. 2-1/2 meters (about 8 feet) length, 1/4” outer diameter.
Please Log In to view prices
Power Supply - Korg, 9V, 500mA~1.2A, Center Negative
For use with MS2000, microKONTROL, microKORG, Etribes, DT7, AX1G/B, AX100G, AX1500, GT12, OT12, and PX3/3B.
Please Log In to view prices
Fan Guard - Metal Grill, Finger Guard
Metal finger-protecting guard for P-HFAN.
Please Log In to view prices
Power Supply - Korg, 12V, 1500mA, Center Positive
Korg Power Supply, KA-310 adapter for X50, MicroX, R3, MR1000, or SP170. Please note that this requires an S-W128 AC power cord to connect to an AC wall outlet.
Please Log In to view prices
Cord - Korg, AC Power, 125 V, 10 A
AC power cord for the Korg KA-310 power adapter (part number M-K080).
This power cord features a standard IEC C7 non-polarized connector that mates with IEC C8 connectors. These are sometimes referred to as "figure 8" or "shotgun" connectors.
Please Log In to view prices
Attenuator - Recycled Sound, Power Plug Lite, -2 dB to -10 dB
The Power Plug Lite offers up to -10db attenuation in a rotary switch with -2db increments. The Power Plug Lite will accept all impedances and is rated for up to 50 watt amps. The same cool extruded aluminum case as the original Power Plug (M-ATT-6-12) for those who want a lighter touch and more control. Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume.
Please Log In to view prices
Attenuator - Recycled Sound, Power Plug 100, -10 dB to -30dB
The Power Plug 100 offers the same -10db as the Power Plug Lite (M-PPLITE) but adds another "Bedroom Level" pot for further attenuation of up to -30dB AND is suitable for amps up to 100 watts! Turn your tube amp UP to drive your power tubes. This is where tube amps blossom and where players get in trouble. Use the attenuator to drop your overall volume to more tolerable levels. You can dial in your breakup, which may be too loud, then attenuate to lower the overall volume. So you can adjust your amp as usual and use the attenuator as an overall Master volume.
Please Log In to view prices
Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter
16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
Please Log In to view prices
Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
Please Log In to view prices
Fuse Holder - for FenderĀ®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
  • Fits ½" chassis hole diameter
  • Mounted by Nut
Please Log In to view prices
Cord - Power, 18 AWG, 3 Conductor, Detachable, Black, IEC
Three conductor, 8 or 12 foot detachable power cord with IEC female end SVT (Marshall type), 18 awg.
Please Log In to view prices
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
Please Log In to view prices
Cord - Replacement Brown, Polarized Plug
2 conductor, 6', brown, 18 awg, polarized plug.
Please Log In to view prices
Cable Clamp - for ¼" Cable Diameter, Nylon
Nylon cable clamp with room for 1/4” cable outer diameter. Perfect for securing cables to cabinet walls. For larger ½” cable clamps see P-HCABLECLAMP-10.
Please Log In to view prices