Power Supplies & Accessories

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut

High quality Fender® Style fuse holder replacement for guitar amplifiers.

• Fits ½" chassis hole diameter
• Mounted by Nut

Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.

I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

Black plastic AC power entry module with built in fuse holder. This power entry module is rated at 10A, 250VAC and fits 5mm x 20mm fuses. Mates with S-W123 & S-W124

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.

Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.

Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.

Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:

• Rated current: 10A
• Rated voltage: 250V AC
• Contact resistance: 2MΩ @ 250V DC or less
• Dialectric withstand: 1 minute @ 1500V AC
• Insulation resistance: 100MΩ or more @ 500V DC

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile bayonet style knob and reduced overall height. The connector at the end of the holder is right angled which reduces the internal depth as well. It is a similar style to fuse holders used on many Fender® amps. Mounting nut and rubber washer included.

Fuse holder cap for Marshall™ 900 series amps. Measures 5/8" in length. Fits into S-H213

Open frame fuse block for GMA or GMD 5×20mm size fuses with a low profile design that features solder terminals made of tin plated brass. A unique design feature provides self-alignment of the clips to the fuse caps. This feature, plus a one-piece clip/terminal design, assures low contact resistance.

High quality fuse holder used with 3AG type fuse. This fuse holder features a low profile design. This holder used 0.187” (4.8mm) quick connect tabs that can also be soldered to. Mounting nut included. 13.2mm hole required for mounting.

Fuse holder cap replacement for P-SP2-500 power receptacle.

Fuse holder cap for the fuse holder found on the Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. This cap fits 3AG fuses and pairs with S-H211.

High quality insulation cover for panel mount fuse holders. The cover is made of a thick durable PVC and fits many fuse holders. The wire sleeve can securely fit over any standard wire gauge used with fuse holders providing a fully insulated fuse connection.
Features

• Provides insulation against shock on rear of fuse holder
• PVC
• UL94V-0 rated flame retardant material

Fits S-H205

Though-hole PCB mount fuse holder used on many Marshall amps such as the 900 series and some 2000 series amps. The fuse cap is sold separately as S-H204. Fits GMA and GMD 5×20mm fuses.

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.
Note: The spade lugs have a detent rather than a hole.

Peavey cap for fuse holder. 1 1/16" length x 3/8" diameter. Top slotted for flat head screwdriver.

Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.

PCB Mount Fuse Cap.

• 1.31” x 0.42”
• Takes GMA sized fuse

New-old-stock Soviet fuse holders. These panel mount holders fit 5x20mm GMA and GMD type fuses. A 0.625” mounting hole is required. Note: A small 0.1” notch must either be filed into the 0.625” mounting hole or filed off of the fuse to flush mount with a panel