Potentiometers

Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.
Trimmer - Bourns, 3352K, Single-Turn, Side Adjust, 1KΩ
Bourns 3352 - ⅜” Round Trimpot. This 1KΩ trimmer features a vertical PCB mount.
Features
  • Single-Turn / Cermet / Industrial / Open Frame
  • Stable cermet element offers infinite resolution
  • Very low profile
  • 3352K pin style
  • Thumb and screwdriver adjustment
Please Log In to view prices
Potentiometer - Dunlop, MXR, 47K, PC mount
Genuine Dunlop replacement potentiometer for Dunlop/ MXR pedals. PC mount, 47K audio taper, knurled shaft.
Please Log In to view prices
Potentiometer - Dunlop Hot Potz, 470 kΩ
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
Please Log In to view prices
Potentiometer - Dunlop, Hot Potz II Crybaby, 100 kΩ
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100 kΩ. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
Please Log In to view prices
Potentiometer - Dunlop, 250 kΩ Audio, for Dunlop GCB80
250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.
Please Log In to view prices
Potentiometer - Dunlop, 1 kΩ FUZZ for the JDF2 Fuzzface
Genuine Dunlop replacement fuzz potentiometer for JDF2 Fuzz Face. 1 kΩ, linear, solid plastic shaft. Made In U.K.
Please Log In to view prices
Potentiometer - Dunlop, 470K kΩ for JH-F1 Jimi Hendrix Fuzzface
Genuine Dunlop replacement potentiometer for Jimi Hendrix JH-F1 Fuzz Face. 470 kΩ, Audio taper, solid plastic shaft. Made In U.K.
Please Log In to view prices
Potentiometer - Dunlop, Wah, 10 kΩ linear
Genuine Dunlop replacement potentiometer for wah/volume.
  • 10 kΩ Linear
  • Gear included
Please Log In to view prices
PCB - Panel Mount Adapter, 9mm Right Angle Potentiometer
Small PCB adapter boards to convert PCB mount 9mm right angle pots to wired panel mount pots. These adapters are great for tight builds allowing for more densely populated panels than 16mm options. They’re also a great way to incorporate sealed potentiometers into builds where larger sized options would be cost prohibitive.
package of 5
Please Log In to view prices
PCB - Panel Mount Adapter, 9mm Vertical Potentiometer
Small PCB adapter boards to convert PCB mount 9mm vertical pots to wired panel mount pots. These adapters are great for tight builds allowing for more densely populated panels than 16mm options. They’re also a great way to incorporate sealed potentiometers into builds where larger sized options would be cost prohibitive.
package of 5
Please Log In to view prices
Dust Cover - Rubber covering for Potentiometers, black
Black dust cover for use with 16mm or 24mm potentiometers. These covers slide over the back of the pot covering the holes and gaps to help prevent dust from accumulating inside avoiding potential repairs and replacing down the road. The dust cover is made of a soft rubbery material and is easy to install on standard 24mm and 16mm pots.
Please Log In to view prices
Potentiometer - 100 Ohm, Original Fender, Control
Original Fender® chassis-mount hum balance potentiometer, 100 ohm.
  • 100-ohm potentiometer used for hum balance control
  • 1/4" threaded brass bushing for mounting to amplifier chassis
  • Adjustable level control (flat-head screwdriver only)
  • Mounting nut and washer included
  • Adjustable from both the front and back face of pot
  • Used for '65 Twin Reverb®, Machete™ and Vibrasonic amplifiers (1992-present) plus others
Please Log In to view prices
Potentiometer - CTS, 10K, Linear, Bias Trimmer, Screw
CTS 10K linear bias potentiometer. This panel mount trimpot is used in many Fender® amplifiers.

Please note: This potentiometer does not include the washer and nut. If you would like to purchase the washer and nut, see our part number R-VNUT-38
Please Log In to view prices
Potentiometer - Marshall, 10kΩ, Linear, Dual, 16mm
10K dual linear, 16mm, 7mm bushing.
Please Log In to view prices
Potentiometer - Fender®, 1M, Solid Shaft
1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.
Please Log In to view prices
Potentiometer - Fender, 1MΩ, J Taper, Solid Shaft, Panel Mount
Original Fender solid shaft 1M potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
Please Log In to view prices
Potentiometer - Marshall, 22kΩ, Linear, Bias, for JMP
22kΩ linear taper. Used as bias / trim potentiometer for JMP.
For a same-brand generic replacement, see R-V25KV-BP.
Please Log In to view prices
Potentiometer - Fender®, 250kΩ, Pan, MN Taper, Solid Shaft
Genuine Fender® 250K pan pot with center detent. Pan pots are also known as balance pots. Solid shaft (1/4") with 3/8” bushing. Mounting hardware not included. See R-VNUT-38 for a compatible nut and washer.
Please Log In to view prices
Potentiometer - Fender®, 250kΩ, Knurled Shaft, Push-Pull
250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
Please Log In to view prices
Potentiometer - Fender®, 250kΩ, Knurled Shaft, No Load
250K ohm. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging. Some Fender guitars have a unique tone circuit that features a "Delta Tone' Control. The "Delta Tone' system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors.
Please Log In to view prices
Potentiometer - Fender®, 250kΩ, Solid Shaft
250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender® packaging.
Please Log In to view prices
Potentiometer - Fender, 250K, Solid Shaft, No Load
250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.
Please Log In to view prices
Potentiometer - Fender®, 250kΩ, J Taper, Solid Shaft, Control
Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
Please Log In to view prices
Potentiometer - 10% Tolerance, Audio, ⅜" Bushing
24mm, solder lug potentiometers with 10% resistance tolerance. These ⅜” bushing pots have an audio taper and the solid shaft fits 6.35mm (¼”) knobs. For linear taper versions, see R-V38-10TOL-XL.
Please Log In to view prices