Potentiometers

1M ohm, Solid Shaft. Original Fender. Used for Volume and Tone control in many Fender guitars as well as amplifiers.

Genuine Marshall replacement potentiometer for MG Series amps. 10 kΩ Linear, D-Shaft.

CTS Audio, Long Shaft 3/4 in. bushing, split knurled shaft, 3/8 in. bushing diameter. Great in guitars that have a thicker carved top (ex. Les Paul) where added bushing length is required.

• Body Diameter: 24 mm
• Power Rating ¼” watt
• Bushing Diameter: ⅜" (Threading: 3/8-32)
• Bushing Length: 3/4"
• Shaft Diameter: ¼"
• Shaft Length: ⅜"
• Tolerance: 20%
• Shaft Material: Brass – Knurled Shaft
• 24 teeth slot and knurled shaft
• Includes (1) Nut and (1) Lock Washer

Genuine Dunlop replacement potentiometer for Dunlop/ MXR pedals. PC mount, 47K audio taper, knurled shaft.

Peavey 20K S-Taper Potentiometer, Spider Style PC Mount Terminals

• Body Diameter: 16mm
• Bushing Diameter: 7mm
• Bushing Length: 5mm
• Shaft Diameter:4.5mm
• Shaft Length:10mm
• Shaft Material: Aluminum – Knurled Split Shaft

500K ohm (audio taper), solid shaft. Made in Taiwan.

250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender^® packaging.

Add a switch to your guitar using the existing holes in your pick guard or body. High quality CTS Push/Pull DPDT switches can be used to add phase switching, coil tapping, series/parallel, etc. to your guitar without having to drill the holes for a mini switch. The shorter body height and side mounted contacts require far less space (1” depth ) making them ideal for thinner bodied guitars with a more shallow body cavity. These Split-shaft pots are compatible with 24- spline, fine knurled knobs and feature a precise audio taper. Hex nuts, flat washer, and lock washer are included with each pot. CTS DPDT pots are available in three types for different applications.

Mini Carbon Element, Push Pull Switch, Dual Audio, Solid Shaft. 17 mm body diameter. 1/4" watt, 300° rotation. DPDT, 6mm shaft diameter. Solder lugs. 3/8" bushing. Bourns® Model PDB183-GTR21 Guitar Potentiometer with Push-Pull Switch. Used for Split-Coil Pickup Switching Electric guitar manufacturing is a multi-billion dollar industry with major manufacturers established worldwide. From the introduction of the first mass-produced electric guitar in 1950, guitarists have been mesmerized with advances in technology and the wide array of after- market parts commercially available for guitar upgrades. Specialty products such as Bourns® Model PDB183-GTR21 Guitar Potentiometer with Push-Pull Switch allow the guitarist multiple functions utilizing a single control such as split-coil switching for humbucking (double-pole) pickups or stacked single-coil pickups, active electronics activation, and pickup phase switching.

Add a switch to your guitar using the existing holes in your pick guard or body. High quality CTS Push/Pull DPDT switches can be used to add phase switching, coil tapping, series/parallel, etc. to your guitar without having to drill the holes for a mini switch. The shorter body height and side mounted contacts require far less space (1” depth ) making them ideal for thinner bodied guitars with a more shallow body cavity. These Split-shaft pots are compatible with 24- spline, fine knurled knobs and feature a precise audio taper. Hex nuts, flat washer, and lock washer are included with each pot. CTS DPDT pots are available in three types for different applications.

Bourns Mini Carbon Element, DPDT Push Pull Switch, Single Audio taper Potentiometer. Split Shaft, Solder Lugs.
This Bourns Guitar Potentiometer with Push-Pull Switch allows the guitarist multiple functions utilizing a single control such as split-coil switching for humbucking pickups or stacked single-coil pickups, active electronics activation, and pickup phase switching.

• 17mm Body Diameter
• 300° rotation
• Power Rating: 0.1 watt
• ¼" Knurled 18-Spline Split Shaft
• DPDT Push-Pull Switch
• ⅜" Bushing Length
• Tolerance: ±20 %
• Maximum Operating Voltage: 150V

250K ohm, audio taper. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging.

Bourns Mini Carbon Element, DPDT Push Pull Switch, Dual Audio, Split Shaft. ¼" watt, 300° rotation. Solder lugs.

• 17mm Body Diameter
• 300° rotation
• Power Rating: 0.1 watt
• ¼" Knurled 18-Spline Split Shaft
• DPDT Push-Pull Switch
• ⅜" Bushing Length
• Tolerance: ±20 %
• Maximum Operating Voltage: 150V
• Bourns Series Number PDB183-GTR21

250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.

250K ohm. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender ® packaging. Some Fender guitars have a unique tone circuit that features a "Delta Tone' Control. The "Delta Tone' system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors.

250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.

Genuine Dunlop replacement fuzz potentiometer for JDF2 Fuzz Face. 1 kΩ, linear, solid plastic shaft. Made In U.K.

Potentiometer cleaning caps for use with aerosol cleaners such as DeoxIT. This is a great tool for difficult to clean potentiometers such as those on hollow body guitars and certain amp chassis. The design pushes the spray in through the bushing of the potentiometer removing the need to access the back of the potentiometer. To use: Remove the knob and thread the cleaning cap onto the potentiometer. If there is enough bushing, attach the rubber o-ring first. If not, simply thread the cleaning cap onto the bushing and place a rag around it. Using a rag is recommended with and without the o-ring. Insert the DeoxIT straw into the small hole on the side of the cleaning cap. Cover the open end with your finger and spray. The cleaning solution is directed to the shaft of the pot where it can seep in. You can turn split shaft pots with a screwdriver through the open end to help move the cleaner around inside the pot.

High quality potentiometers from AxLabs. These audio taper pots feature a ¼” bushing and a ¼” (6.35mm) solid shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These linear taper pots feature a ⅜” bushing and coarse (T18) knurled shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These linear taper pots feature a ¼” bushing and coarse (T18) knurled shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These linear taper pots feature a ⅜” bushing and ¼” (6.35mm) solid shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These linear taper pots feature a ¼” bushing and a ¼” (6.35mm) solid shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These audio taper pots feature a ⅜” bushing and coarse (T18) knurled shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.