Potentiometers are used to control volume and tone. A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider.Check out our Tech Corder articles on pots, including Potentiometer Types.
Potentiometer - Fender®, 250kΩ, J Taper, Solid Shaft, Control
Original Fender solid shaft 250K potentiometer with J taper. 3/8-32 threading. The resistance between wiper and cold lug measures about 25% at half-way shaft rotation.
Potentiometer - Fender, 3M, Reverse Audio, Solid, 16mm, Snap-In
Genuine Fender® replacement 3 Meg Ω potentiometer with a reverse audio taper. This snap in bracketed pot is used as the tremolo speed control pot in many Fender reissue amps that use PCBs for the front panel controls. Mounting hardware not included.
Potentiometer - Fender, 1MΩ, J Taper, Solid Shaft, Panel Mount
Pot, Solid Shaft, 1M J Taper
Potentiometer - Bourns, Audio, Knurled Shaft, ¾" Bushing
Bourns Audio Potentiometer, Premium, Conductive Polymer, Solder Lugs
- 0.625" W x 0.625" L x 0.5" D
- 300° rotation
- Power Rating: ¼ watt
- ¼" Knurled 18-Spline Split Shaft
- ¾" Bushing Length
- Tolerance: ±20 %
- Very Low Noise
Potentiometer - Fender, 250K, Solid Shaft, No Load
250K ohm, solid shaft, no load. Some Fender guitars have a unique tone circuit that features a "Delta Tone" Control. The "Delta Tone" system consists of a high output bridge pickup and special 'no-load' tone control for the middle and bridge pickups. This new pot has a detent at the 10 position which bypasses completely any filtration through capacitors. Unlike the TBX, which has a detent at the 5 position and gradually reduces the amount of filtration through the capacitor, the Delta-Tone's 'no-load' feature eliminates filtration completely at the detent and the result is more of the direct presence of the pickup.
Potentiometer - Bourns, Linear, Knurled, Conductive Polymer
Linear, .75" bushing length. Conductive polymer, 0.625" W x 0.625" L x 0.5" D body. ¼" watt, 300° rotation. ¼" shaft diameter. Solder lugs. 3/8" bushing. Knurled split shaft.
Potentiometer - Peavey, 20kΩ S-Taper, Spider
Peavey 20K S-Taper Potentiometer, Spider Style PC Mount Terminals
- Body Diameter: 16mm
- Bushing Diameter: 7mm
- Bushing Length: 5mm
- Shaft Diameter:4.5mm
- Shaft Length:10mm
- Shaft Material: Aluminum – Knurled Split Shaft
Potentiometer - 100kΩ, Wah Replacement, Life, Smooth
100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.
Potentiometer - PMT, Dual Mode Tone Control
The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!
Potentiometer - 500kΩ, Audio, Knurled Long, DPDT, Push-Push
DPDT switch, ¼" split knurled shaft, audio taper. 3/8-32 threads, 16mm body diameter. .75" bushing length, .38"-.52" shaft length.
Potentiometer - PMT, Humbucker Control, Coil Filters
The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.
Potentiometer - PMT, CTS, Audio, Variable Treble Bleed, ⅜"
The V-Treb Variable Treble Bleed Circuit for guitar and bass is available pre-installed on high quality volume pots from CTS and Bourns. The circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Turning the trim pot clockwise increases the amount of treble bypass for a brighter sound at reduced volumes. Turning the trim pot counter clockwise reduces the amount of treble bypass for a warmer tone at reduced volumes. With the volume at 10, the V-Treb is removed from the circuit and does not affect the sound. The V-Treb circuit also also available separately for use on any other volume pot.
Potentiometer - Peavey, 50kΩ, Linear, Center Detent
50K Linear, spider. Center detent. See R-VPV-50KL-R for a version without detent. Mounting hardware not included.
Potentiometer - Peavey, 50K, Linear, Switch
50K Linear, with push/pull switch. Mounting hardware not included.
Potentiometer - Peavey, 50K, Linear, Wire Wound, 30 Detents
50K Linear, wire wound, XL shaft. 30 detents evenly-spaced throughout its rotation. Mounting hardware not included.
Potentiometer - Alpha, Reverse Audio, 9mm, Right Angle, 25KΩ
Reverse audio taper (antilog), right angle, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are poplar in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.
Potentiometer - Fender®, 250kΩ, Knurled Shaft, Push-Pull
250K ohm (audio taper), push-pull DPDT, split shaft. Made in Korea.
Nut & Washer - Panel, for ⅜" Potentiometers and Jacks
Package of 100Replacement nut and washer for pots and jacks that feature a ⅜" bushing with 3/8-32 threading. Sold in packs containing 100 nuts and 100 washers.
Potentiometer - PMT, Audio, Variable Treble Bleed, ¾"
Precision Music Technologies V-Treb with 500KA CTS pot – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced. Pot: 24 mm body diameter, ¼” knurled split shaft. Bushing diameter = 3/8”, Bushing Length = 3/4”. PCB dimentions: 1.06” x 0.46” x 0.07”
Potentiometer - Dunlop, 250 kΩ Audio, for Dunlop GCB80
250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.
Potentiometer - PMT, V-Treb, Audio Treble Bleed, ⅜" shaft
Precision Music Technologies V-Treb – Variable Treble Bleed Bypass Circuit. Made in USA. The V-Treb variable treble bleed/bypass circuit corrects the problem of high frequency losses at reduced volumes by allowing the player to control how bright or warm the tone will get as the volume control is reduced.
Potentiometer - 500kΩ, Linear, Knurled Long, DPDT, Push-Push
- DPDT Push-Push switch
- ¼" split knurled shaft
- Linear taper
- 3/8-32 threads
- 16mm body diameter (widest point on switch body 17.8mm)
- 75" bushing length
- 38"-.52" shaft length.
Potentiometer - Peavey, 10kΩ, Audio, Slide, 100mm
10K Audio, 100mm. Pin spacing: 4.870" x 0.191".
Trimmer - Bourns, 3362P, Single Turn, Top Adjust, PCB Mount
High-quality Bourns 3362P trimpots. These single-turn cermet trimmers can be found in countless guitar pedals and synthesizer modules. Sealed trimmers are built with an o-ring seal to prevent entrance of moisture and serve as a mechanical restraint to prevent unwanted wiper movement. ±10% tolerance.