Pedal Parts / DIY

Prewired steel low-profile LED bezel with a diffused LED. With a 0.061” height, this steel LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12V. Mounting nut and rubber o-ring included.

Prewired low-profile LED bezel with a diffused LED. With a 0.07” height, this black metal LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12V. Mounting nut and rubber o-ring included.

Prewired cone-shaped LED bezel. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12V. Mounting nut and lock washer included.

CD4015B consists of two identical, independent, 4-stage serial-input/parallel-output registers. Each register has independent CLOCK and RESET inputs as well as a single serial DATA input. "Q" outputs are available from each of the four stages on both registers. All register stages are D-type, master-slave flip-flops. The logic level present at the DATA input is transferred into the first register stage and shifted over one stage at each positive-going clock transition. Resetting of all stages is accomplished by a high level on the reset line.

CD4024B is a 7-stage ripple-carry binary counter. All counter stages are master-slave flip-flops. The state of a counter advances one count on the negative transition of each input pulse; a high level on the RESET line resets the counter to its all zeros state. Schmitt trigger action on the input-pulse line permits unlimited rise and fall times.

The CD4052B analog multiplexers are digitally-controlled analog switches having low ON impedance and very low OFF leakage current.

The CD4077B contains four independent Exclusive-NOR gates. The CD4077B provides the system designer with a means for direct implementation of the Exclusive-NOR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4077B - Quad Exclusive-NOR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.

CD4007UB types are comprised of three n-channel and three p-channel enhancement-type MOS transistors. The transistor elements are accessible through the package terminals to provide a convenient means for constructing the various typical circuits as shown in Fig. 2. More complex functions are possible using multiple packages. Numbers shown in parentheses indicate terminals that are connected together to form the various configurations listed. Features:

• Standardized symmetrical output characteristics
• Medium Speed Operation — tPHL, tPLH = 30 ns (typ.) at 10 V
• 100% tested for quiescent current at 20 V
• Meets all requirements of JEDEC Tentative Standard No.

CD4017B is a 5-stage Johnson counter having 10 decoded outputs, respectively. Inputs include a CLOCK, a RESET, and a CLOCK INHIBIT signal. Schmitt trigger action in the CLOCK input circuit provides pulse shaping that allows unlimited clock input pulse rise and fall times. These counters are advanced one count at the positive clock signal transition if the CLOCK INHIBIT signal is low. Counter advancement via the clock line is inhibited when the CLOCK INHIBIT signal is high. A high RESET signal clears the counter to its zero count. Use of the Johnson counter configuration permits high-speed operation, 2-input decode-gating and spike-free decoded outputs. Anti-lock gating is provided, thus assuring proper counting sequence. The decoded output are normally low and go high only at their respective decoded time slot. Each decoded output remains high for one full clock cycle.

The CD4040B is a 12-stage ripple-carry binary counter. All counter stages are master-slave flip-flops. The state of a counter advances one count on the negative transition of each input pulse; a high level on the RESET line resets the counter to its all zeros state. Schmitt trigger action on the input-pulse line permits unlimited rise and fall times.

The CD4070B contains four independent Exclusive-OR gates. The CD4070B provides the system designer with a means for direct implementation of the Exclusive-OR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4070B - Quad Exclusive-OR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.

CD4093B consists of four Schmitt-trigger circuits. Each circuit functions as a two-input NAND gate with Schmitt-trigger action on both inputs. The gate switches at different points for positive- and negative-going signals. The difference between the positive voltage (VP) and the negative voltage (VN) is defined as hysteresis voltage (VH). Features:

• Schmitt-trigger action on each input with no external components
• Hysteresis voltage typically 0.9 V at VDD = 5 V and 2.3 V at VDD = 10 V
• Noise immunity greater than 50%
• No limit on input rise and fall times
• Standardized, symmetrical output characteristics
• 100% tested for quiescent current at 20 V
• Maximum input current of 1 µA at 18 V over full package-temperature range, 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V parametric ratings
• Meets all requirements of JEDEC Tentative Standard No.

MKII fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board.The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. For modern versions of this board, see P-PC-BEND-MKII-X.

FZ-1 fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Maestro FZ-1 pedals. The board is styled after the original version that can also be found in early serial Maestro FZ-1A pedals. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets (sold separately). The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Eyelet-Rite fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the germanium Mosrite Fuzzrite pedals. The board is styled after the point to point version that used eyelets. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets and is directly mounted to a Carling P-H550 footswitch (both sold separately). The original build also used a unique C350K pot and the R-VOMSL-350KRA is the perfect substitute. The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

MKIII & MKIV fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Vox Tone Bender MKIII pedals. The board is styled after the non-reverse version that can also be found in the Park Fuzz Sound, Rotosound Fuzz, and the MKIV Tone Bender. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses a unique PCB mount potentiometer R-VOMUP-100KL. A matching enclosure P-HROTO-1 can be used with the board to complete a vintage style fuzz build. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

V828 Italian fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the V828 Vox Tone Bender pedals. The board is styled after the Italian made version which was also sold as the Jen Fuzz. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses unique PCB mounted tags for the offboard wiring. A combination of S-HEYE-A eyelets and S-H137 solder tags (each sold separately) can be used to approximate the originals. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Supa Fuzz style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the SupaFuzz pedal. The board is styled after the first version that Marshall produced which featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Flat-washer style solder tag for use with M3.5 or #6 screws. This small solder tag is an easy way to add a wire such as a chassis ground connection to a build. This solder tag is also a great match for vintage style builds such as Fuzz Face style effects pedals.

• Contact Material: Brass
• Contact Plating: Tin
• Inner Diameter: 3.5± 0.2 mm
• Outer Diameter: Ø6.3 ± 0.2 mm
• Length: 12.7 ± 0.5 mm
• Thickness: 0.35 mm

Peavey TRS jack with a switched tip connection. Stereo HID (High Definition), insulated, plastic bushing.

Shatterbox style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Shatterbox pedal. The board is styled after the later version with a printed circuit rather than a stripboard construction. This is the same board that was used in the “split board” version which can be built by cutting the board down the middle to separate the fuzz section from the treble booster section. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws.

Zonk Machine style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk Machine pedal. The board is styled after the early version that featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

HS Treble Booster style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Hornby Skewes ‘Treble Booster’ pedal. The board is styled after a version of the silicon Treble Booster but can be used for the germanium version as well. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using a screw. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Zonk II style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk II pedal. The board is styled after the version that featured silicon transistors and a printed circuit rather than a stripboard construction. It is actually a cut down version of the Shatterbox PCB using only the fuzz side of that pedal. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.