Pedal Parts / DIY

DPDT momentary footswitch. AC125V/4A AC250V/2A. Rated for 50,000 make-and-break cycles at full load.

Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

PCB for converting SMD TQFP-64 packages to through hole DIP-64 footprints with 0.9" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

High quality plated ⅜” nuts for jacks and potentiometers. These nuts are perfect for amplifier, pedal and synthesizer builds with high aesthetics or color theming. The ⅜”-32 UNEF-2A threading fits many ⅜” bushing parts such as Switchcraft ¼” jacks and CTS pots.

Genuine Dunlop replacement small knurled knob for MXR pedals. Push -on style knob designed for use with coarse knurled shafts.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.

Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.

Plastic wing knobs with set screws and brass insert. These knobs are a close match for the classic knobs used on Marconi radios and Neve consoles. They feature an inlay indicator line. The grip diameter is 0.693 inches with a 1 inch clear skirt. Fits ¼” (6.35mm) pot shafts.

Handheld suction type solder remover.

Set screw with brass insert, ¼" shaft. Measures 1.28" diameter x .71" tall.

Eyelet-Rite fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the germanium Mosrite Fuzzrite pedals. The board is styled after the point to point version that used eyelets. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets and is directly mounted to a Carling P-H550 footswitch (both sold separately). The original build also used a unique C350K pot and the R-VOMSL-350KRA is the perfect substitute. The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

The BC549 is a silicon general purpose NPN transistor in a TO-92 package. The BC549’s typical applications include signal processing, amplification, and switching. The BC549 is available in two different gain ranges: BC549B and BC549C. Type hFE (IC=2mA, VCE=5V) BC549B 200-450 BC549C 420-800

50V ceramic capacitors with 5mm footprints for use in amplifiers, stomp boxes, and any other electronic project. These capacitors are small and should easily fit in any sized project. These also feature 1” lead lengths so they work great for point to point wiring.

5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.

PCB and parts kit for the Iss 1 fuzz built in the style of the standard germanium Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs feature a slotted set screw, and fit ¼" solid shaft potentiometers. These are a close match to the Davies 1400.

• Height: 0.43 in.
• Length: 0.825 in.
• Fits ¼" shaft with set screw

High-quality solder lug audio taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.

• Solder lug / panel mount
• Audio taper
• +/- 10% tolerance
• ¼” (6.35mm) solid shaft
• Machine-pressed dust seal
• High quality wiper material
• Low residual resistance

For linear taper solder lug pots see R-VGORVA-BX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.

Replacement seal for S-H910 and S-H911 Cliff UK jacks.

Premium versions of the pseudo eyelet boards with 7.5mm spacing. The premium versions feature 2.4mm thick boards with gold plated contacts. These PCBs have similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. For standard versions, see P-HTB-X. 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 7.5mm x 26mm eyelet spacing
• 57.15mm x 30.66mm board
• 45mm spacing for 3.2mm mounting holes
• Great fit for 125B and 1590N1 enclosures

2x12 Board:

• 2 rows of 12 eyelets (24 total)
• 7.5mm x 26mm eyelet spacing
• 87.15mm x 30.66mm board
• 75mm spacing for 3.2mm mounting holes
• Great fit for 1590BB enclosures

Two rows of 18 U-style terminals (36 total) on a black board. This U-style terminal strip is extra dense with 6.35mm terminal spacing allowing for even more densely populated point-to-point builds. The boards are 0.063” thick.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Six 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.

Electrical tape for splicing and insulating wires up to 600V. Rubber adhesive with soft polyvinyl chloride film backing. UL Listed.

High-quality USA made knobs from Rogan Corp. These small, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.

• Height: 0.71 in.
• Diameter:0.57 in.
• Fits 6mm D Shafts
• Indicator on round side of D-shaft

For a T18 knurled version of this knob, see P-K271PS-W. A variety of different sizes are available from the PT Series.