Pedal Parts / DIY

The CD4069UB device consists of six CMOS inverter circuits. These devices are intended for all general-purpose inverter applications where the medium-power TTL-drive and logic-level-conversion capabilities of circuits such as the CD4009 and CD4049 hex inverter and buffers are not required. Features:

• Standardized symmetrical output characteristics
• Medium speed operation: tPHL, tPLH = 30 ns at 10 V (Typical)
• 100% Tested for quiescent current at 20 V
• Maximum input current of 1 µA at 18 V over full package-temperature range, 100 nA at 18 V and 25°C
• Meets all requirements of JEDEC tentative standard No. 13B, Standard Specifications for Description of B Series CMOS Devices

J201 N-Channel JFET in a TO-92 package made by Siliconix. The J201 is designed primarily for low level audio and general purpose applications with high impedance signal sources.

• Max drain to gate voltage = 40 V
• Max gate to source voltage = -40 V
• Max forward gate current = 50 mA

OPA134 single op amp in an 8-pin DIP package. The OPA134 series are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.

GCB-95 latching switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Carbon Film resistors are made by vacuum depositing a thin carbon film on a ceramic form. A good choice for applications which require a steady, low power drop. Package of 5. These resistors are perfect for pedal builders! 1/4 watt ± 5% tolerance EIA color coded .24" long x .08" diameter Resistance Values (5 each) 100 470 1K 2.7K 4.7K 8.2K 10K 22K 33K 47K 100K 150K 220K 470K 560K 1M

Cliff UK 1/4" white jack, switched. 4 PC mount terminals include: tip, tip-shunt, sleeve and sleeve-shunt. External threading: 7/16-20. Features:

• Low-noise Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability
• 'Kinked' legs for snap-in PCB mounting on PC-A and PC-C styles to facilitate pre-assembly and wave soldering
• Tough, molded grade 1 white Nylon body.
• Made in the U.K.
• Supplied with a white nylon hexagonal mounting nut
• Designed to receive both mono and stereo 1/4" jack plugs

• Withstand Voltage: 2000VDC Min.
• Maximum Current: 5A
• Temperature Rating: -10°C ~ +70°C
• Life (Minimum): 10,000+ Operations
• Nominal Contact Resistance: < 50 mΩ

High voltage warning label for amplifiers and other equipment. These stickers are a great option for labeling equipment and builds as high voltage whenever necessary. The sticker is a single piece that must be cut to size using scissors or a paper cutter to make a total of four labels. This style of label is perfect for rear panels on amplifiers and other equipment.

Eight conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).

Standard size terminal strips, 1/16 thick bakelitetin plated steel solder lugs and brackets on 3/8" centers. 5 lug 1 ground first lug common

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Adzam (Mazda) brand OC45 PNP germanium transistors. The OC45 is a popular PNP for fuzz pedals and boost effects. This transistor is in a glass SO-2 package with long leads commonly found on germanium transistors. The dot indicates the collector lead.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.

Padboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid of pads and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each square pad is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated square shaped pads
• 20 x 10 holes
• 3.04” x 1.55”

Fender R/A 1/4" stereo jack. Used 1999-present. Hex nuts not included (S-H510), bushing length = 0.34".

Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.

Large 6.02” x 3.27” x 1.98” Hammond 1590P1 enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

2N1305 PNP germanium transistors. The 2N1305 is a popular PNP for fuzz pedals and other effects. This transistor is in a TO-5 package with long leads commonly found on germanium transistors.

2 to 1 heat shrink tubing variety pack with multiple colors in each size. This pack includes six different diameters ranging from 1/16” to 3/8”. Each piece is 4” in length. This set comes in a hard plastic case perfect for sorting and storing heat shrink. Features:

• Resistant to common fluids and solvents
• UL and CSA listed
• UV resistant
• Meets DEF. STAN 59.97
• Meets UL 224, 125°C and CSA C22.2 No. 198.1
• Meets MIL-DTL-23053/5 Class 2 & 3
• Flame retardant (Does not include transparent)
• Seals and protects cable splices and terminations.
• Thin wall tubing

Included Sizes (Diameter):

• 60 pieces - 1/16 in.
• 35 pieces - 3/32 in.
• 25 pieces - 1/8 in.
• 20 pieces - 3/16 in.
• 10 pieces - 1/4 in.
• 10 pieces - 3/8 in.

This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.

Handheld suction type solder remover.

Turret strip, with 6 turrets. Measures 67mm x 15.875mm.