Pedal Parts / DIY

P-Q972 Diode - 1N34A Germanium
The 1N34A Germanium diode is an old standby in electronics. Widely used for detecting the rectifying efficiency or for switching on a radio, TV or stereo etc.
Please Log In to view prices
P-QCD4016 CMOS - CD4016, Quad Bilateral Switch, 14-Pin DIP
CD4016B Series types are quad bilateral switches intended for the transmission or multiplexing of analog or digital signals. Each of the four independent bilateral switches has a single control signal input which simultaneously biases both the p and n device in a given switch on or off. Features:
  • 20-V digital or ± 10-V peak-to-peak switching
  • 280- typical on-state resistance for 15-V operation
  • Switch on-state resistance matched to within 10 typ. over 15-V signal-input range
  • High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k
  • High degree of linearity: <0.5% distortion typ. @ fis = 1 kHz, Vis = 5 Vp-p, VDD–VSS
  • Extremely low off-state switch leakage resulting in very low offset current and high effective off-state resistance: 100pA typ.
Please Log In to view prices
P-LPW-FLAT-X LED with Bezel - Low Profile, Prewired, Diffused LED, Steel
Colors Available:
Prewired steel low-profile LED bezel with a diffused LED. With a 0.061” height, this steel LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and rubber o-ring included.
Please Log In to view prices
P-K384X Knob - Plastic, Set Screw, Vertical Pointer, 0.51" Diameter
Colors Available:
Small plastic control knob with set screw and brass insert. This knob features a radial-brushed metal top, a fine straight-knurl grip, and a vertical pointer. Fits ¼” (6.35mm) pot shafts.
Please Log In to view prices
W-SC-11 ¼" Jack - Switchcraft, Mono, open circuit
Switchcraft Type 11 Little-Jax phone jack. Mono 2-conductor, open circuit. Mates with standard ¼" plugs and is available with standard or long bushings. Great replacement for Fender® guitar & amp input jacks.
Please Log In to view prices
S-H9FER-BLK Ferrule - for Cliff UK Jacks, Black Plastic
Genuine Cliff ferrule for internal thread S4 jacks (3/8-20). This matte black ferrule works great with the S-H960-X washers to provide a unique look for inputs on amplifiers, pedals, and other equipment.
Please Log In to view prices
S-B872 Cloth Pedal Bag - 4” x 6”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
Please Log In to view prices
S-T-PK366D Desoldering Pump - Manual, for removing solder
Handheld desoldering pump for solder removal. The enhanced dual spring-loaded piston creates a powerful vacuum for easy removal of molten solder. The static free tip is self cleaning and made from a clog resistant material. The aluminum body is lightweight and durable.
Please Log In to view prices
S-H170X Standoff - #6-32, Male-Female, Aluminum
#6-32 threading, package of 4. Comes in 1/2" or 3/4" length. For female standoffs, see S-H172X
package of 4
Please Log In to view prices
P-QTC7660 Regulator - TC7660S, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC7660S charge pump voltage converter in an 8 pin DIP package. The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+.
Please Log In to view prices
P-Q-XMN3007 Integrated Circuit - Xvive, MN3007, BBD, 1024 Stage
The XVive MN3007 is a drop-in replacement for the original Panasonic 1024-stage MN3007 BBD chip used in many chorus, vibrato, and flanger pedals and effects. The MN3007 is a 1024-stage, low-noise, long-delay BBD that provides a signal delay of up to 51.2 milliseconds. Due to its long delay times, the MN3007 is especially suitable for reverb effects in electronic musical instruments and PA equipment.
Please Log In to view prices
P-L700-X LED - 5mm, Water Clear, High Brightness, Package of 5
Colors Available:
High brightness 5mm LED. Great for use in pedal and amp builds as well as other applications where a bold, bright, indicator is needed. Multiple colors available.
  • 5mm size
  • Water clear
  • High brightness
  • Multiple colors available
  • Package of 5
package of 5
Please Log In to view prices
P-H501 Footswitch - 3PDT, Blue, Taiwan-made, latching-type
Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in Taiwan.
Please Log In to view prices
P-PC-FUZZ-ISS2-BRN PCB - Vintage Style Circuit Board, Iss. 2 Fuzz, Phenolic Board
Iss. 2 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 2 circuit board found in classic Fuzz Face pedals. The iss. 2 version uses NPN silicon transistors. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. For the germanium iss. 1 version of this board, see P-PC-FUZZ-ISS1-BRN.
Please Log In to view prices
P-PC-SSDIP-20 PCB - SMD to Thru-Hole Adapter, SSOP-20 to DIP-20
PCB for converting SMD SSOP-20 packages to through hole DIP-20 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
package of 5
Please Log In to view prices
P-H54-DRESS-THRU Nut - Dress Nut, Threaded Through, For Mini Toggle Switches
Threaded through dress nuts for use with mini toggle switches. Unlike the other versions of this dress nut, this nut is not capped allowing the nut to thread past the top of the switch’s bushing. The uncapped top can be useful where internal depth is an issue such as parallel PCB mounting. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.
Please Log In to view prices
P-ECB-31 Felt Pad - Dunlop, replacement for Wahs
Replacement Dunlop felt pad for use with wah pedals. This circular felt pad has an adhesive side for an easy installation. The pad is typically installed on the underside of the pedal directly above the footswitch to cushion the contact when switching the wah on and off. Made in USA.
Please Log In to view prices
P-0401H Terminal Strip - 4 Lug, 2nd Lug Common, Horizontal
Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.
package of 5
Please Log In to view prices
P-QOP275 Op-Amp - OP275, Dual, Bipolar/JFET, Audio, 8-Pin DIP
OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.
Please Log In to view prices
P-Q2SC945 Transistor - 2SC945, TO-92 case, NPN
2SC945 NPN transistors. This is a silicon NPN transistor in a TO-92 package. The 2SC945 was used in many classic Boss pedals such as the CE-2 chorus.
Please Log In to view prices
S-H906 ¼" Jack - Cliff, Mono, PC Mount, L-leg, Tin
  • Withstand voltage: 2000V DC Minimum
  • Maximum current: 5A
  • Temperature rating: -10°C - 70°C
  • Life (minimum): 10,000+ operations
  • Nominal contact resistance:
Please Log In to view prices
P-K345X Knob - Plastic, Set Screw, MXR Style, 1.0" Diameter
Colors Available:
Large plastic knobs with set screw and brass insert. Similar to the knobs used on many classic Dunlop / MXR pedals. These knobs have a fluted grip with an indicator line as well as a dot indicator on the skirt. Fits ¼” (6.35mm) pot shafts.
Please Log In to view prices
P-PC-BEND-MKII-BRN PCB - Vintage Style Circuit Board, MKII Fuzz, Phenolic Board
MKII fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board.The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. For modern versions of this board, see P-PC-BEND-MKII-X.
Please Log In to view prices
P-QBC546X Transistor - BC546, General Purpose, TO-92 case, NPN
The BC546 is a silicon general purpose NPN transistor in a TO-92 package. The BC546’s typical applications include signal processing, amplification, and switching. The BC546 is available in two different gain ranges: BC546B and BC546C. Type hFE (IC=2mA, VCE=5V) BC546B 200-450 BC546C 420-800
Please Log In to view prices