Pedal Parts / DIY

Potentiometer - GØRVA, Linear, 16mm, Solder Lug, Solid Shaft
High-quality solder lug linear taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.
  • Solder lug / panel mount
  • Linear taper
  • +/- 10% tolerance
  • ¼” (6.35mm) solid shaft
  • Machine-pressed dust seal
  • High quality wiper material
  • Low residual resistance

For audio taper solder lug pots see R-VGORVA-AX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.
Please Log In to view prices
Knob - Rogan, PT Series, 1PS, Small, Skirted, Pointer, Knurled Shaft
High-quality USA made knobs from Rogan Corp. These small, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm T18 knurled shafts.
  • Height: 0.71 in.
  • Diameter: 0.57 in.
  • Fits T18 Knurled Shafts

For a D-shaft version of this knob, see P-K281PS-W. A variety of different sizes are available from the PT Series. See the links below for the full selection of knurled shaft knobs from this series. P-K271P-W 1P Small Pointer P-K272P-W 2P Medium Pointer P-K272PS-W 2PS Medium Skirted Pointer
Please Log In to view prices
Knob - Rogan, PT Series, 2PS, Medium, Skirted, Pointer, D-Shaft
High-quality USA made knobs from Rogan Corp. These medium, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.
  • Height: 0.84 in.
  • Diameter: 0.62 in.
  • Fits 6mm D Shafts
  • Indicator on round side of D-shaft

For a T18 knurled version of this knob, see P-K272PS-W. A variety of different sizes are available from the PT Series.
Please Log In to view prices
LED with Bezel - Low Profile, Prewired, Diffused LED, Steel
Colors Available:
Prewired steel low-profile LED bezel with a diffused LED. With a 0.061” height, this steel LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and rubber o-ring included.
Please Log In to view prices
Transistor - 2N5458, JFET, N-Channel,TO-92
2N5458 N-channel JFET in a TO-92 package. The 2N5458 is an N−channel junction field effect transistors, depletion mode (Type A), designed for audio and switching applications. Features
  • N−Channel for Higher Gain
  • Drain and Source Interchangeable
  • High AC Input Impedance
  • High DC Input Resistance
  • Low Transfer and Input Capacitance
  • Low Cross−Modulation and Intermodulation Distortion
Please Log In to view prices
Integrated Circuit - 24LC32A/P, EEPROM, 8-pin DIP
24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.
Please Log In to view prices
Power Jack - Cliff, DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
Please Log In to view prices
Battery Clip / Snap - for 9 Volt batteries
9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.
package of 3
Please Log In to view prices
Header - Round Pin, 20 Position, Breakaway, 2.54mm Spacing
20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:
  • Round Pin
  • 20 Position
  • 2.54mm Spacing
  • Breakaway
Please Log In to view prices
Integrated Circuit - PT2399, Echo / Delay
PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.
Please Log In to view prices
¼" Jack - Rean, Mono, Open Circuit
2 pole open 1/4" jack, 2 contacts, with washer and nut, panel thickness 3.5 mm, with 0.205" faston tabs
Please Log In to view prices
PCB - Pseudo Eyelet Board, 7.5mm Spacing
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.
Please Log In to view prices
Cable Tie Mount - Nylon, Adhesive Backing
Colors Available:
Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.
package of 5
Please Log In to view prices
¼" Jack - Open Circuit, Made in Taiwan
¼" female. Open circuit. Replacement for Fender®. Made in Taiwan.
Please Log In to view prices
Ribbon Cable - Flexstrip, 6 Conductor
Six conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics.
Please Log In to view prices
LED with Bezel - Low Profile, Prewired, Diffused LED, black metal
Colors Available:
Prewired low-profile LED bezel with a diffused LED. With a 0.07” height, this black metal LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and rubber o-ring included.
Please Log In to view prices
Diode - KD521V, Silicon, used in Russian Big Muff
New-old-stock Soviet silicon diodes KD521V (КД521B) in a SOD27 package. These diodes were used in EHX/Sovtek Big Muff models from Civil War to Black Russian. The KD521V is a high-speed switching diode encapsulated in hermetically sealed, leaded glass. The SOD27 packages are similar to DO-35.
Please Log In to view prices
Transistor - 2N6027 Programmable Unijunction
2N6027 programmable unijunction transistor often referred to as a PUT. The 2n6027 can be found in many tremolo effects pedal projects.
Please Log In to view prices
Op-Amp - OP07, Single, Precision, Low Offset, 8-Pin DIP
OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.
Please Log In to view prices
Transistor - 2N5457, JFET, N-Channel, TO-92
2N5457 N-Channel JFET in a TO-92 package. The 2N5457 is designed primarily for audio and switching applications.
  • Max drain to gate voltage = 25 V
  • Max gate to source voltage = -25 V
  • Max forward gate current = 10 mA
Please Log In to view prices
Transistor - 2SD77, Germanium, TO-1 case, NPN
2SD77 NPN germanium transistors. The 2SD77 is a popular NPN for fuzz pedals and other effects. The NPN polarity allows for use with standard pedal power supplies.
Please Log In to view prices
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Please Log In to view prices
Transistor - J201, JFET, N-Channel, MMBFJ201 Presoldered TO-92 Adapter
Surface mount MMBFJ201 JFETs presoldered to TO-92 adapter boards. Use wire, clipped component leads, or pin headers to easily attach these adapters to PCBs using TO-92 footprints for J201s. These JFETs can be found in many effects pedals, synthesizers, and other projects. The J201 / MMBFJ201 is an N-Channel general purpose amplifier JFET. This device is designed primarily for low level audio and general purpose applications with high impedance signal sources. The pinout is marked on the PCB and is DSG when facing the component side.
Please Log In to view prices
Switch - GØRVA, Mini Toggle, SPDT, 2 Position, Solder Lugs, Medium Bat
Premium two position SPDT mini toggle switches from Gorva Design. The Bascular Mini switches have a medium 7.5mm actuator length. These switches feature silver plated copper contacts. RoHS compliant & lead-free. Mounting hardware included. Details
  • 8.89 mm bushing length
  • Medium bat
  • 2-Position On/On
  • ¼" mounting hole diameter
  • Single pole/Double throw (SPDT)
  • Solder lugs

Features:
  • Power Rating: DC9V, 1A
  • Contact Resistance: <10mΩ
  • Insulation Resistance: 1000MΩ Minimum
  • Dielectric Strength: 1000V RMS @ Sea Level
  • Operating Temperature: -40°C ~ +85°C
  • Electrical Life: 40,000 Cycles
  • RoHS & Lead-free
Please Log In to view prices