Pedal Parts / DIY

Battery Clip - Premium, 9 Volt, Rigid Frame, I-Style
Premium 9V battery clip with a rigid plastic frame and I-style wire orientation. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
Please Log In to view prices
Transistor Set - tested and selected for Fuzz Face, 2N1309, PNP, Germanium
This is a set of two 2N1309 germanium transistors that have been hand-selected to work in the germanium Fuzz Face circuit. Also included are 4 metal film resistors to use in the circuit. In most cases, the values have been modified from the stock values slightly to ensure that the collector of Q2 biases to roughly -4.5V. A data sheet containing the schematic and the resistor values is included so that you can use your own resistor type if you would prefer. There is a range of bias voltages that can sound nice in a Fuzz Face, and voltages in original units varied. These transistors have been tested with bias voltage, sound, and noise level in mind. Note that due to a variety of factors such as battery/PSU voltage, temperature, and component tolerance, the voltage on the collector of Q2 may not measure at exactly -4.5V, but it should be close in a properly-built circuit.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Supa Fuzz, Phenolic Board
Supa Fuzz style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the SupaFuzz pedal. The board is styled after the first version that Marshall produced which featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, MKII Fuzz, Phenolic Board
MKII fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board.The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. For modern versions of this board, see P-PC-BEND-MKII-X.
Please Log In to view prices
PCB - Vintage Style Circuit Board, FZ-1 Fuzz, Phenolic Board
FZ-1 fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Maestro FZ-1 pedals. The board is styled after the original version that can also be found in early serial Maestro FZ-1A pedals. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets (sold separately). The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Eyelet-Rite Fuzz, Phenolic Board
Eyelet-Rite fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the germanium Mosrite Fuzzrite pedals. The board is styled after the point to point version that used eyelets. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets and is directly mounted to a Carling P-H550 footswitch (both sold separately). The original build also used a unique C350K pot and the R-VOMSL-350KRA is the perfect substitute. The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, MKIII & MKIV Fuzz, Phenolic Board
MKIII & MKIV fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Vox Tone Bender MKIII pedals. The board is styled after the non-reverse version that can also be found in the Park Fuzz Sound, Rotosound Fuzz, and the MKIV Tone Bender. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses a unique PCB mount potentiometer R-VOMUP-100KL. A matching enclosure P-HROTO-1 can be used with the board to complete a vintage style fuzz build. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, V828 Italian Fuzz, Phenolic Board
V828 Italian fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the V828 Vox Tone Bender pedals. The board is styled after the Italian made version which was also sold as the Jen Fuzz. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses unique PCB mounted tags for the offboard wiring. A combination of S-HEYE-A eyelets and S-H137 solder tags (each sold separately) can be used to approximate the originals. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
Solder Tag - M3.5 or #6 Mounting Hole
Package of 12
Flat-washer style solder tag for use with M3.5 or #6 screws. This small solder tag is an easy way to add a wire such as a chassis ground connection to a build. This solder tag is also a great match for vintage style builds such as Fuzz Face style effects pedals.
  • Contact Material: Brass
  • Contact Plating: Tin
  • Inner Diameter: 3.5± 0.2 mm
  • Outer Diameter: Ø6.3 ± 0.2 mm
  • Length: 12.7 ± 0.5 mm
  • Thickness: 0.35 mm
Please Log In to view prices
PCB - Vintage Style Circuit Board, HS Treble Booster, Phenolic Board w/ mount
HS Treble Booster style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Hornby Skewes ‘Treble Booster’ pedal. The board is styled after a version of the silicon Treble Booster but can be used for the germanium version as well. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using a screw. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Zonk II, Phenolic Board w/ mount
Zonk II style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk II pedal. The board is styled after the version that featured silicon transistors and a printed circuit rather than a stripboard construction. It is actually a cut down version of the Shatterbox PCB using only the fuzz side of that pedal. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Shatterbox, Phenolic Board w/ mount
Shatterbox style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Shatterbox pedal. The board is styled after the later version with a printed circuit rather than a stripboard construction. This is the same board that was used in the “split board” version which can be built by cutting the board down the middle to separate the fuzz section from the treble booster section. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Zonk Machine, Phenolic Board w/ mount
Zonk Machine style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk Machine pedal. The board is styled after the early version that featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
Please Log In to view prices
Terminal Pin - PCB Mount, 0.05” Diameter, 0.25” Length
PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.
Please Log In to view prices
Chassis Box - Hammond, 1456, 15° Aluminum/Wood, 4" x 5.5" x 2"
Colors Available:
15° sloped aluminum consoles from Hammond’s 1456 Series with wood sides. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes.
Features:
  • 4" x 5.5" x 2" (1” height at front)
  • Top panels are 0.064” thick aluminum
  • Powder coated top and bottom
  • Wood sides are real walnut - each piece has a unique color & grain.
  • Solid oiled walnut sides on a black, ventilated steel base.
  • Comes with self adhesive rubber feet and required mounting hardware.
Please Log In to view prices
Knob - Chicken Head, Raised, set screw
Colors Available:
New!:
Raised plastic chickenhead knob with brass insert and set screw. 1.20" in length. Davies 2300 clone.
Please Log In to view prices
Knob - Chicken Head, set screw, brass inset
Colors Available:
New!:
  • Fits ¼" Solid Shafts (Set Screw)
  • Chicken head knobs are used everywhere on countless amps, stomp-boxes, etc.
  • Brass Set Screw and Insert
  • High Quality Plastic
Please Log In to view prices
PCB - Vintage Style Circuit Board, Iss. 2 Fuzz, Phenolic Board
Iss. 2 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 2 circuit board found in classic Fuzz Face pedals. The iss. 2 version uses NPN silicon transistors. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. For the germanium iss. 1 version of this board, see P-PC-FUZZ-ISS1-BRN.
Please Log In to view prices
Battery Clip - Vintage Style, 9 Volt, Fiberboard Frame
9V battery clip with a fiberboard frame. This high quality battery snap features tinned brass eyelets that secure the nickel-plated steel contacts to the fiberboard. Wires can be soldered directly to the eyelets allowing for custom length battery connections. This fiberboard style is similar to the 9V battery connectors in vintage electronics such as the Arbiter Fuzz Face.
Please Log In to view prices
9V Battery Cushion- Vinyl Foam Tape, 3M, ½” x 2”
1/2 inch by 2 inch adhesive foam strip for cushioning 9V batteries in pedal enclosures. This black, medium density foam used an acrylic adhesive and paper liner. The high quality 3M materials ensure a durable foam and lasting adhesive. Made with ¼ inch thick foam.
Please Log In to view prices
Amp-top Enclosure - Hammond, 20 ga. Steel, 4" x 6" x 3"
High quality powder coated amp-top enclosures from Hammond’s 1454 Series. These cases are a great choice for amp top effects such as the Dallas Rangemaster. Features
  • Made of strong, economical 20 gauge steel.
  • Rugged powder coat finish: beige panels with textured black covers.
  • Choice of sloping or vertical front panels by reversing the case.
  • 6-32 Philips nickel plated screws and self-adhesive rubber feet included.
Please Log In to view prices
Trimmer - BI Technologies, Sealed, Cermet , Top Adjust, 10kΩ
High-quality BI Technologies Model 82 trimpots. These single-turn cermet trimmers are sealed ensuring a long life. They feature long leads (0.62”) making them a great choice for point to point builds in addition to PCB mounting. The simplistic design also looks great in vintage style builds.
Please Log In to view prices
Knob - Phenolic, Set Screw, Chicken Head
High quality phenolic knob with a classic chicken head design. This knob has an infilled indicator line. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
  • Height: 0.485 in.
  • Length: 1.25 in.
  • Fits ¼" shaft with set screw
  • Brass Insert
  • High Quality Phenolic
Please Log In to view prices
Knob - Painted Phenolic, Set Screw, Premium RCA Style, 33mm Skirt, Pointer
Colors Available:
Painted phenolic knobs with a set screw and brass insert. These unique knobs closely match the colorful RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. These classic knobs are painted to match the style of the original painted RCA knobs. The paint is a durable chip-resistant coating. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts.
  • Height: 0.792 in. (20.1 mm)
  • Diameter: 1.293 in. (33 mm)
  • Fits ¼" shaft with set screw
Please Log In to view prices