New Products

Fuse Holder - for Marshall, 3AG Type, PCB Mount
Though-hole PCB mount fuse holder used on many Marshall® JCM2000 series such as the TSL100, TSL122, DSL50, and DSL100 as well as other amps. Check footprint and dimensions for compatibility. This holder fits 3AG fuses and pairs with the S-H212 cap. Cap sold separately.
Please Log In to view prices
Transistor - AS394H, Matched Pair, Alfa, TO5-8 case, NPN
The AS394H is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.
Please Log In to view prices
Integrated Circuit - AS3340A, VCO, Alfa, 16-Pin Dip
The AS3340A is Alfa’s version of the CEM3340 IC. The AS3340A is a completely self-contained, precision voltage controlled oscillator, featuring both exponential and linear control scales and up to four buffered output waveforms: triangle, sawtooth, square, and pulse with voltage controllable pulse width. Full temperature compensation makes these VCOs extremely stable, and eliminates the need for a temperature compensation resistor. The highly accurate exponential and linear control inputs are virtual ground summing nodes, allowing multiple control voltages to be mixed within the device itself.
Also included is provision for hard and soft synchronization of the frequency, and an output for easy adjustment of high frequency tracking. Special care in the design ensures oscillation start-up under any power-on sequence and supply conditions.
An on-chip 7.4 volt Zener diode allows the device to operate off ±15 volt supplies, as well as +12, -5 volt supplies.
Please Log In to view prices
Integrated Circuit - AS3310, VC ADSR, Alfa, 16-Pin Dip
The AS3310 is Alfa’s version of the CEM3310 IC. The AS3310 is a self-contained, precision ADSR type of envelope generator intended for electronic music and other sound generation applications. Attack, decay and release times are exponentially voltage controllable over a wide range, and the sustain level is linearly voltage controllable from 0 to 100% of the peak voltage Vp. All four control Inputs are Isolated from the rest of the circuitry so that the control pins of tracking units may be simply tied together.
On the negative power output, there is an internal Zener diode at 7.4 volts ± 10%, which allows the chip to supply a maximum voltage of ± 15 volts with a current-limiting resistor REE, and a minimum positive supply voltage of + 11 volts and a minimum negative supply voltage of -5 volts.. A series current limiting resistor must be added between pin 6 and the supply.
Please Log In to view prices
OTA - AS3080ED, Linearizing Diodes, Alfa, SOIC-8
The AS3080ED is Alfa’s version of the CA3080 IC in an SOIC package. The AS3080ED is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080ED has differential input and a single-ended, push-pull, class A output. Amplifier bias input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080ED is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.
Please Log In to view prices
OTA - AS3280D, Dual, Linearizing Diodes, Alfa, SOIC-16
The AS3280 is Alfa’s version of the CA3280 IC in an SOIC package. The AS3280D consists of two variable operational amplifiers that are designed to substantially reduce the initial input offset voltage and the offset voltage variation with respect to changes in programming current. This design results in reduced "AGC thump," an objectionable characteristic of many AGC systems. Careful design of critical places of the circuit reduces the amplifier dependence upon thermal and processing variables.
The AS3280D has all the generic characteristics of an operational voltage amplifier except that the forward transfer characteristics is best described by transconductance rather than voltage gain, and the output is current, not voltage. The magnitude of the output current is equal to the product of transconductance and the input voltage.
Please Log In to view prices
OTA - AS3080E, Linearizing Diodes, Alfa, 8-Pin DIP
The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.
Please Log In to view prices
Fuse Holder - 3AG-Type, High Quality, Low Profile
High quality fuse holder used with 3AG type fuse. This fuse holder features a low profile design. This holder used 0.187” (4.8mm) quick connect tabs that can also be soldered to. Mounting nut included. 13.2mm hole required for mounting.
Please Log In to view prices
Transistor - AS194H, Matched Pair, Alfa, TO5-8 case, NPN
The AS194H is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.
Please Log In to view prices
OTA - LM13700, Dual, Linearizing Diodes and Buffers, 16-Pin DIP
The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.
Please Log In to view prices
Transistor - AS395H, Matched Pair, Alfa, TO5-8 case, PNP
The AS395 dual monolithic PNP transistor offers excellent parametric matching and high frequency performance. Low noise characteristics (1 nV/√Hz typ @ 1 kHz), high bandwidth (190 MHz typical), and low offset voltage (100 µV max), makes the AS395 an excellent choice for demanding preamplifier applications.Tight current gain matching (3% max mismatch) and high current gain (100 min), over a wide range of collector current, makes the AS395 an excellent choice for current mirrors. A low value of bulk resistance makes the AS395 an ideal component for applications requiring accurate logarithmic conformance. To ensure the long-term stability of the matching parameters, internal protection diodes across the base-emitter junction clamp any reverse base-emitter junction potential.
Please Log In to view prices
Transistor - AS394CH, Matched Pair, Alfa, TO5-8 case, NPN
The AS394CH is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.
Please Log In to view prices
Integrated Circuit - AS3360, Dual VCA, Alfa, 14-Pin Dip
The AS3360 is Alfa’s version of the CEM3360 IC. The AS3360 is a dual general purpose voltage controlled transconductor intended for such applications as voltage controlled amplifiers, filters, and waveform generators. Each transconductor independently provides both linear and exponential control scaling over greater than a 100 dB range. Complete with virtual ground summing inputs, wide voltage compliance current outputs, and control inputs referenced to ground, the AS3360 requires exceptionally few external components and is extremely easy to use. Because of its inherent ultra-low control feedthrough, no trimming is required.
Please Log In to view prices
Integrated Circuit - AS3320, Multi-Mode VCF, Alfa, 18-Pin Dip
The AS3320 is Alfa’s version of the CEM3320 IC. The AS3320 is a high performance voltage controlled four-pole filter with on-chip voltage controllable resonance IC. The four independent sections may be interconnected to provide a wide variety of filter responses, such as low pass, high pass, band pass and all pass. A single input exponentially controls the frequency over greater than a ten octave range with little control voltage feedthrough. Another input controls the resonance in a modified linear manner from zero to low distortion oscillation. For those demanding applications, provision has been made to allow trimming for improved control voltage rejection. Each filter section features a variable gain cell which is fully temperature compensated, exhibits a better signal-to-noise ratio and generates its low distortion predominantly in the second harmonic. The device includes a minus two volt regulator to ensure low power dissipation and consequent low warm-up drift.
Please Log In to view prices
OTA - AS3280, Dual, Linearizing Diodes, Alfa, 16-Pin DIP
The AS3280 is Alfa’s version of the CA3280 IC. The AS3280 consists of two variable operational amplifiers that are designed to substantially reduce the initial input offset voltage and the offset voltage variation with respect to changes in programming current. This design results in reduced "AGC thump," an objectionable characteristic of many AGC systems. Careful design of critical places of the circuit reduces the amplifier dependence upon thermal and processing variables.
The AS3280 has all the generic characteristics of an operational voltage amplifier except that the forward transfer characteristics is best described by transconductance rather than voltage gain, and the output is current, not voltage. The magnitude of the output current is equal to the product of transconductance and the input voltage.
Please Log In to view prices
Potentiometer - Alpha, Linear, 9mm, Vertical
Linear taper, vertical mount, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.
Please Log In to view prices
Wire - Gavitt, Cloth, 18AWG Stranded, Top Coat Pre-Tinned
Sold by the foot
Colors Available:
High quality USA made Gavitt. This wire features an outer waxed cotton braid over a celanese braid. The wire is stranded 18AWG with a tinned overcoat (topcoat) so no additional tinning with a soldering iron is required for use. Sold by the foot.
Please Log In to view prices
Pedal Kit - Mod® Electronics, Seismic / Shift, JFET Boost
The Seismic / Shift is a JFET boost based on one of the earliest effects to ever be used on stage. This pedal adds subtle color to a guitar's sound while maintaining the natural tone of the guitar. It packs a serious punch that can cut through any mix when soloing or whenever some extra “umph” is required. The Seismic Shift pairs nicely with amps and other pedals. Place it ahead of tubes, preamps, overdrives, distortions, and fuzz pedals to shift your gear onto a new level. The Seismic Shift pedal kit is the introduction to the Nexus Series from Mod Electronics. This series features a PCB base rather than the Mod Electronics’ traditional point-to-point wiring kits to offer builders an even wider variety of effects to build. The Seismic Shift kit is designed for all skill sets and is the perfect first build for those unfamiliar with PCB construction. The pedal operates on both 9VDC and 18VDC.
Please Log In to view prices
Pedal Kit - Mod® Electronics, The Ring In Return, Octave-Up Fuzz
The Ring In Return is an octave-up fuzz effect that is an all-analog design that captures those late 60s octave-up fuzz tones. Transformer-coupled germanium diodes produce sounds that range from a subtle octave-up to thick, harmonically-rich sonic textures and synth-like tones. Experimenting with different pickups and tone-control settings on your guitar with The Ring In Return can also produce sitar-like sounds. Warning: This circuit was designed for use with a 9 VDC power supply only.
Please Log In to view prices
Cover - Tele, Neck, 1950s Style, USA
Colors Available:
New!:
Original, made in USA, covers for 1950s, vintage-style, tele neck pickups. These premium tele covers are made of nickel silver and feature the long skirt associated with ‘50s era pickups.
Please Log In to view prices
Bridge - Wraparound, Vintage Spec, Aluminum, USA
Colors Available:
New!:
U.S. made and true to vintage 1950s specifications. This lightweight (35 grams) wraparound bridge is made of aluminum to match the original 1950s version. High quality plating is used on all options. Each side is adjustable using the included hex set screws to dial in the intonation. Mounting studs sold separately. For a full set with all hardware included, please see P-GKLU-KLP1127N.
  • 3.22 in. (82mm) stud spacing
Please Log In to view prices
Wire - Magnet, 42 AWG, Elektrisola, P155 Heavy
High quality 42AWG Elektrisola P155 magnet wire with heavy (two coats) enamel. Perfect for winding coils, pickups, or transformers. Properties
  • Very good solderability
  • High thermal properties

Applications
  • Small transformers
  • Relays
  • Solenoids
  • Small motors
  • Watch coils
  • Transformers
  • Instruments

Please note: Product length is based on weight and may vary slightly from the listed values. SKU Weight Approx. Length S-MW-42-2OZ 2 oz. 6200 ft S-MW-42-4OZ 4 oz. 12400 ft S-MW-42-8OZ 8 oz. 24800 ft S-MW-42-1LB 1 lb 49600 ft
Please Log In to view prices
Transistor - BC108C, TO-18 case, NPN
BC108C NPN silicon transistors. The BC108C is a popular NPN choice for fuzz pedals and other effects such as vintage silicon Fuzz Face builds and Big Muff clones.
  • NPN polarity
  • Collector emitter breakdown voltage 25V
  • Collector base breakdown voltage 30V
  • Collector current 200mA
  • Power 0.75W
  • Transition frequency 150MHz
  • TO-18 case
  • Weight 0.35g
Please Log In to view prices
Nut - Wide Dress Nut, Threaded Through, For Mini Toggle Switches
Threaded through wide dress nuts for use with mini toggle switches. This wide based nut is not capped allowing the nut to thread past the top of the switch’s bushing. The uncapped top can be useful where internal depth is an issue such as parallel PCB mounting. These plated dress nuts feature a wide chamfered edge for a professional and unique look. These work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.
Please Log In to view prices