New Products

Bridge - Nashville Tune-O-Matic, Zinc, USA
Colors Available:
New!:
Made in U.S. modern-spec tune-o-matic bridge with no retaining wire. This bridge is fully plated and comes with pre-slotted saddles. Mounting hardware sold separately. For a full set with all hardware included, please see P-GKLU-KLP120XC. This Nashville bridge is a great upgrade that features wider intonation adjustments and a larger mass for better tone and sustain.
  • Post spacing: 2.93 inches (74.5mm)
  • Radius: 12 inches (30.48cm)
  • String Spacing: 10.4 mm
  • For use with 4.95mm stud posts
Please Log In to view prices
Knob - Phenolic, Set Screw, Premium RCA Style, Skirted, Pointer
Phenolic skirted knobs with a set screw and brass insert. These unique knobs closely match the RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts. 22mm Skirt:
  • Height: 0.495in. (12.6 mm)
  • Diameter: 0.875 in. (22 mm)
  • Fits ¼" shaft with set screw

26mm Skirt:
  • Height: 0.656 in. (16.7 mm)
  • Diameter: 1.02 in. (26 mm)
  • Fits ¼" shaft with set screw

33mm Skirt:
  • Height: 0.792 in. (20.1 mm)
  • Diameter: 1.293 in. (33 mm)
  • Fits ¼" shaft with set screw

40mm Skirt:
  • Height: 0.865 in. (22 mm)
  • Diameter: 1.568 in. (40 mm)
  • Fits ¼" shaft with set screw
Please Log In to view prices
Knob - Phenolic, Set Screw, Retro Pointer
High quality phenolic pointer knob with a vintage design. The retro pointer has a thick band that extends above the base allowing for easy manipulation of the knob making it a great option for rotary controls and switches. This solid phenolic knob has an infilled indicator line with a decorative diamond shaped top. Fits 0.25” (6.35mm) shafts with set screw and brass insert. This knob pairs perfectly with the smaller P-K356 knob.
  • Height: 0.85 in.
  • Length: 1.63 in.
  • Fits ¼" shaft with set screw
Please Log In to view prices
Faceplate Mount - Marshall, Cabinet Logo Frame
Original Marshall™ cabinet logo frame. This mounts to original Marshall™ cabinets using two screws. The adhesive backed badge is then adhered to this frame. Faceplates sold separately.
  • Fits 1960 cabinets
  • Black plastic
  • For 29 x 85mm logos
  • Screw mount
Please Log In to view prices
Knob - Phenolic, Set Screw, Orange Amp Style, Skirted
Phenolic skirted knobs with a set screw and brass insert. These fluted round knobs are close matches for the classic knobs used on Orange Amps. Each knob features a painted dot indicator on the skirt. Fits ¼” (6.35mm) pot shafts. 19mm Skirt:
  • Height: 0.61 in. (15.5 mm)
  • Diameter: 0.74 in. (19 mm)
  • Fits ¼" shaft with set screw

28mm Skirt:
  • Height: 0.61 in. (15.5 mm)
  • Diameter: 1.1 in. (28 mm)
  • Fits ¼" shaft with set screw

42mm Skirt:
  • Height: 0.79 in. (20 mm)
  • Diameter: 1.645 in. (42 mm)
  • Fits ¼" shaft with set screw
Please Log In to view prices
Knob - Phenolic, Set Screw, Stealth Chicken Head
High quality chicken head style knob with a unique angular design. The stealth chicken head has a thin band that extends above the base allowing for easy manipulation of the knob. This solid phenolic knob has an infilled indicator line. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
  • Height: 0.7 in.
  • Length: 1.408 in.
  • Fits ¼" shaft with set screw
Please Log In to view prices
Diode - 1N60, Germanium, Striped Clear Glass, DO-7
1N60 point-contact germanium diodes in a DO-7 package with striped clear glass. 1N60 diodes were used in many vintage electronics and also make for great clipping diodes in stompbox effects pedals.
Please Log In to view prices
Threadlocker - Bob Smith Industries, IC-LOC Green
IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC™ Green wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners. Uses
  • Threads of fasteners
  • Bolts
  • Screws
  • Nuts

Directions: Shake well. Unscrew cap and cut off tip. Apply IC-LOC™ Green to clean preassembled fasteners. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Green prevents the loosening of threaded fasteners from shock and vibration by wicking into threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Locked fasteners are only removable by localized heating and hand tools. Remove residue with a damp cloth. Similar to Loctite Green.
Please Log In to view prices
Tool - Potentiometer Cleaning Cap, Aluminum
Potentiometer cleaning caps for use with aerosol cleaners such as DeoxIT. This is a great tool for difficult to clean potentiometers such as those on hollow body guitars and certain amp chassis. The design pushes the spray in through the bushing of the potentiometer removing the need to access the back of the potentiometer. To use: Remove the knob and thread the cleaning cap onto the potentiometer. If there is enough bushing, attach the rubber o-ring first. If not, simply thread the cleaning cap onto the bushing and place a rag around it. Using a rag is recommended with and without the o-ring. Insert the DeoxIT straw into the small hole on the side of the cleaning cap. Cover the open end with your finger and spray. The cleaning solution is directed to the shaft of the pot where it can seep in. You can turn split shaft pots with a screwdriver through the open end to help move the cleaner around inside the pot.
Please Log In to view prices
PCB - Vintage Style Circuit Board, MKI Fuzz
This board is a recreation of the MKI circuit board found in early Tone Bender pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKI boards were hand drilled, the holes have an organic layout that was somewhat unique to each build. This board follows the exact hole pattern of one of these original builds. The build style is also fairly unique in the MK1. It is a point to point style board without eyelets or turrets. The leads of the parts are wrapped upward around the edge of the board and then solder is applied to connect the components. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.
Please Log In to view prices
PCB - Vintage Style Circuit Board, MKII Fuzz
This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board. The traces are gold plated making soldering easier than most stripboards. Additionally the plating provides protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.
Please Log In to view prices
PCB - Pseudo Eyelet Board, 7.5mm Spacing
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.
Please Log In to view prices
PCB - Vintage Style Circuit Board, Iss. 1 Fuzz
This PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. There are numerous great parts choices available for this PCB.
Please Log In to view prices
PCB - Pseudo Eyelet Board, 9.1mm Spacing
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 9.1mm horizontally and 34.4mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for 7.5mm spacing 2x8 Board:
  • 2 rows of 8 eyelets (16 total)
  • 9.1mm x 34.4mm eyelet spacing
  • 69.42mm x 40.1mm board
  • 54.6mm spacing for 3.2mm mounting holes
  • Great fit for 1590P1, Gorva S90, and YY slanted enclosures

2x10 Board:
  • 2 rows of 10 eyelets (20 total)
  • 9.1mm x 34.4mm eyelet spacing
  • 87.1mm x 40.1mm board
  • 72.8mm spacing for 3.2mm mounting holes
  • Great fit for 1590BB enclosures
Please Log In to view prices
Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style, Shielded Eyelets
Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
Please Log In to view prices
PCB - Charge Pump, -9V from +9V, 3PDT Switch Mount
3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
Please Log In to view prices
PCB - Charge Pump, -9V from +9V, Screw Mount
Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
Please Log In to view prices
Turret Strip - Socket Mount , Gold Plated Copper, Single Row
Single row turret strips with a tab for mounting directly to tube socket mounting holes. The screw mount turrets are made of gold plated brass and are pre-mounted to the 2mm thick boards. The mounting hole is 0.15” in diameter. These turret strips are a great option for components connecting to the socket lugs of point to point builds.
Please Log In to view prices
Paper Label Tag - Pre-strung, Manilla, 2.75” x 1.375”
Package of 10
High quality manila paper tags. These tags are pre-strung with a soft string gentle enough to use on the most delicate equipment. The paper is heavy duty 13 point stock and the ¼” eyelet is reinforced to resist tearing. These are great tags for pricing, labeling, and cataloging equipment.
Please Log In to view prices
IC Socket - Dual in-line package, 2.54mm Pitch, 7.62mm Spacing
IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.
Please Log In to view prices
Capacitor - CE Mfg., 450V, 80/40/40µF
CE Manufacturing USA Made Multi Section Can Capacitor. Reproduced To Exact Mallory Specs Using Original Mallory Machinery
  • 80/40/40uF - 450VDC Electrolytic
  • FP / Twist Lock Style. Solder Tabs
  • -10%, +50% Tolerance, 55°C Temperature Rating
  • 1 ⅜"D X 4"H
Please Log In to view prices
Potentiometer Adapter Sleeve - Converts 4mm shaft to 6mm
This nickel-plated steel adapter sleeve converts a 4mm shaft potentiometer to 6mm shaft, allowing for 6mm knobs to be used on a wider range of potentiometers. An additional 6mm to 6.35mm adapter R-VADAPT-25 can then be used to fit 1/4” knobs (sold seperately).
Please Log In to view prices
Finishing Washer - Blackface / Silverface, Plated Metal
Package of 10
Colors Available:
New!:
Plated metal finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. These high quality washers closely resemble the washers found on many vintage blackface and silverface amplifiers. Fits with #8 countersunk screws.
Please Log In to view prices
Washer - Flat, M12, Stainless Steel, Oversized
Colors Available:
Oversized M12 flat washers. These washers fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches and full-sized toggle switches. These oversized washers are a great way to add a distinctive look to projects.
Please Log In to view prices