Pedals & Kits

The Mod® Electronics Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.

The K-GMOD-3S is a vintage style wiring kit for Les Paul guitars. This version comes with short bushing pots for flat top Les Paul’s. Use this kit to upgrade your current Les Paul electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

PCB and parts kit for the Supa Fuzz. This is based on the classic PCB version produced by Marshall. This kit includes all of the resistors and capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

Adjusting volume control and gain controls provides a wide variety of tones in spite of its simple construction. The Turbo switch provides an additional boost in volume and less internally generated distortion. It is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life.

The K-GMOD-5 is a vintage style wiring kit for Les Paul toggle switches and output jacks. Use this kit to upgrade your current Les Paul switch and jack to high quality parts.

The Mod® Electronics Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The Dwell control adjusts the input signal level driving the tank and the Reverb control adjusts the level of output reverberations from the tank. The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank. MOD® reverb tanks are deemed the closest to the original reverb tanks from the '60s made today. The Wave's reverb function can be switched in and out pop-free via the front panel toggle or with a footswitch. Footswitch sold separately (see P-H470 for compatible footswitch).

PCB and parts kit for the HS Treble Booster. This is based on the more common silicon version that used a 2N4061 transistor. This kit includes all of the resistors, and capacitors used on the included circuit board. A 2N4061 transistor is included. In addition to the PCB parts, a footswitch, jacks, battery snap, and ground lug are all included in this parts kit.

The Mod® Electronics Contortionist II kit is an all analog, high octane fuzz box. It produces fuzz with layered octave overtones similar to those produced by an electronic-bow. The frequency multiplier circuitry creates harmonics that swell and recede depending on gain setting, pick attack, neck position and pickup. This is a high gain circuit that can put out up to 2 volts and will provide ample amounts of sustain. The Contortionist II has all the features of the original Contortionist with an added tone control for a wider range of sounds, and an LED that lights up when the unit is activated.

The Maxon GE601 graphic equalizer is the perfect tool for dialing in guitar tone. The six bands are set with slide potentiometers offering precision controls with a visual representation of the sound spectrum. Each band can both cut and boost sound for a variety of tonal shaping effects as well as frequency specific boost effects.
Features

• Six-band graphic eq with an overall level volume capable of producing various sounds
• Bands cover 100Hz to 3.2KHz for effective tone shaping with guitars
• Each band can cut or boost providing a variety of uses
• LED indicator for effect on/off
• DC power or 9V battery
• Made in Japan

The Mod® Electronics Erratic Clutch Deluxe is a unique effect pedal kit that gives you fuzzy square wave distortion as well as a monophonic sub-octave square wave using a total of only four transistors. The two signals can be used individually or mixed together for a raw and sonically rich synthy output. Full of character and quirk, this pedal will give you a truly original sound. The middle knob is the bias control. This adjusts the pulse width in the initial fuzz stage of the pedal. Set this knob to fit your pickups and playing style. The closer to the center the longer the note will sustain but with that comes more chaotic tracking for the divider. Moving it more clockwise or counterclockwise will give you more predictable note tracking on the divider with less sustain.

The Mod® Electronics Saturator is an overdrive pedal kit that can cover a wide range of gain effects, transitioning smoothly from a massive clean boost to a warm and saturated distortion with the turn of a knob. The saturation is controlled with the Soak knob, which dials in the amount of symmetrical soft-clipping applied to the guitar signal. When fully counterclockwise, the signal is unaffected and clean. Rotating the knob clockwise will incrementally increase the soft-clipping, morphing from a clean signal through subtle-to-heavy saturated overdrive sounds and straight into distortion territory. The Level knob sets the overall volume of the clean or saturated output. Unity gain is at roughly 8 o'clock. With the Soak set to clean, rotating the Level knob clockwise will increase the level to upwards of 30dB.

PCB and parts kit for the MKII fuzz pedal. This is based on the classic stripboard Tone Bender Professional. This stipboard fuzz circuit was also used in some versions of the Supa Fuzz as well as some other fuzz pedals. This kit includes all of the resistors, capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

PCB and parts kit for the V828 fuzz pedal. This is based on the classic Italian-made V828 Tone Bender. These were also sold under the Jen brand. This kit includes all of the resistors, capacitors, and solder tags used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

PCB and parts kit for the Zonk Machine. This is based on the original PCB version. This kit includes all of the resistors and capacitors used on the included circuit board. The germanium PNP transistors are not included such that customers can select and test their own.

The Ring In Return is an octave-up fuzz effect that is an all-analog design that captures those late 60s octave-up fuzz tones. Transformer-coupled germanium diodes produce sounds that range from a subtle octave-up to thick, harmonically-rich sonic textures and synth-like tones. Experimenting with different pickups and tone-control settings on your guitar with The Ring In Return can also produce sitar-like sounds. Warning: This circuit was designed for use with a 9 VDC power supply only.

Snubber parts kit for circuits. Used to build a "snubber circuit" to remove unwanted high frequencies and high voltages resulting from output transformer ringing in a guitar amplifier, without the "brick wall" effect of using diodes.

The OD9Pro+ is the OD9 with all of the bells and whistles. This pedal features the famous circuit with some of the most popular mods built in and accessible with the flip of a switch. The OD9Pro+ offers the classic overdrive sound of the original and can push even further with the boost switch engaged.

PCB and parts kit for the Iss 2 fuzz built in the style of a BC183KA Fuzz Face. This kit includes all of the resistors, capacitors, and transistors used on the included circuit board. For the BC183KA style parts kit, a pair of BC183A transistors are included.

Kit components for the Ham Nation Field Strength Meter project. From HAMNation episode 289.

The K-GMOD-4 is a vintage style wiring kit for PRS guitars. Use this kit to upgrade your current PRS electronics to high quality parts. This kit also includes a treble bleed mod for the volume pot to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

The K-GMOD-6 is a vintage style wiring kit for ES-335 guitars. Use this kit to upgrade your current ES-335 electronics to high quality parts. This kit also includes a treble bleed mod for the volume pots to enhance clarity with lower settings and comes with detailed instructions and all the parts you need to make your modification.

Junior Genius Kits are built for experimentation, learning and fun! Experience the joy of seeing your first LED light up. The Blinky Lights Kit leads you through 10 core activities, from a simple LED circuit up to more advanced transistor LED blinky light circuits, using standard parts on a real-world breadboard. Learn about voltage and current by using LEDs, resistors, capacitors and transistors. You'll be able to build circuits using a schematic diagram, and there's plenty of help to get you there. Simple examples make it easy to grasp the basics and 'What's Happening' and 'Things To Try' sections encourage you to dig deeper. You will get valuable assembly and troubleshooting experience as you learn to use a great experimentation tool, the solderless breadboard. Real hands-on experience means greater educational value. This next-generation science kit doesn’t seal the parts into simplified plastic blocks.

The OOD9 is the updated version of the original Maxon overdrive pedal, the OD880. This overdrive is equipped with NJM4558D op amps for a warm and low-noise overdrive that pairs perfectly with tube amplifiers and other distortion pedals. The OOD9 offers a dynamic response that preserves the tone of the input providing a smooth and clear overdriven sound.

The PAC9 is a classic analog chorus featuring swirling warm chorus sounds and stereo output for a wide chorus spread. In addition to the standard Speed and Width controls, the PAC9 offers a Bright switch for a focused sound and a Pure switch that boosts the signal. Features

• Clean analog chorus sound using the Maxon MC4107D BBD chip
• Speed and Width controls
• Bright and Pure switches offer a variety of sounds for bold and deep chorus effects
• Widely adjustable Speed range of 0.33Hz - 8Hz.