Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.

The Mod® Electronics Piledriver is a clean-boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!

The Mod® Electronics MOD 102 is a great place to start for those interested in building their own tube amp. It is based on a classic American tube-circuit design combined with a British style Class A output tube section. At low volume it produces a clean chimey tone that moves into smooth overdrive at higher volumes. All parts are included along with a pre-drilled steel chassis, wire and tubes (1 EL84 and 1 12AX7). Puts out at least 5 watts. The chassis layout is open for easy assembly using the clear, easy to follow instructions.

The Maxon OD808 is an identical circuit to the original TS808 Tubescreamer Maxon designed and built in the late 1970s. Featuring a JRC4558, the OD808 offers the same natural overdriven tones as the original pedals used widely across all genres of music. The OD808 has a warmer and smoother tone than the OD-9 that pairs nicely with clean amps in addition to sounding great in just about any rig.
Features

• Natural and smooth overdrive effects with tube-like saturation
• Preserves the original tone of the instrument
• Produces a variety of sound ranging from a clean boost to fully saturated overdrive
• LED indicator for effect on/off
• DC power or 9V battery
• Made in Japan

The Maxon OD-9 is the original Tube Screamer TS9 circuit built by the company that designed this immensely popular overdrive pedal. They left no boxes unchecked by including a genuine JRC4558 and the only departure from the original is the inclusion of true bypass switching, a modern necessity. The OD-9 offers slightly more gain than the OD808.
Features

• Identical to the original circuit and featuring the JRC4558 IC chip
• Natural tube-like overdrive that smoothly responds to dynamic signals
• True Bypass Switching
• Low noise mechanical switch
• LED indicator for effect on/off
• DC power or 9V battery
• Made in Japan

The RAT2 is the classic distortion pedal in the Pro Co RAT family. It has a unique tone structure that other effect devices are measured against. The beauty of the RAT 2 lies in its versatility. Used as a primary distortion, it excels at arena rock rhythm tones and soaring leads.

The Mod® Electronics Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.

Adjusting volume control and gain controls provides a wide variety of tones in spite of its simple construction. The Turbo switch provides an additional boost in volume and less internally generated distortion. It is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life.

The Mod® Electronics Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal. Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged. All you need to provide is solder and tools! Uses 9 volt battery which is not included.

This radio kit will cover the AM radio band along with the SW radio band. Power for this receiver is 1.5 V DC for the filaments and 45V DC for the plate current. A D cell and five 9V transistor batteries wired in series will work to power this radio. A 2000 ohm headset or an audio amplifier is required. Requires two T-1T4_DF91 tubes (not included).