Integrated Circuits

Audio Power Amplifier - LM386N-1 / 4, Low Voltage
LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.
Please Log In to view prices
Op-Amp - OP07, Single, Precision, Low Offset, 8-Pin DIP
OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.
Please Log In to view prices
Op-Amp - OP275, Dual, Bipolar/JFET, Audio, 8-Pin DIP
OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.
Please Log In to view prices
Regulator - TC7660S, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC7660S charge pump voltage converter in an 8 pin DIP package. The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+.
Please Log In to view prices
Regulator - TC1044, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.
Please Log In to view prices
IC Socket - Dual in-line package, 2.54mm Pitch, 7.62mm Spacing
IC component sockets for dual in-line package chips (DIP, PDIP, DIL, DIPP.) These sockets feature ladder style cases with tinned stamped and formed connections.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, QFN-32 to DIP-32
PCB for converting SMD QFN-32 packages to through hole DIP-32 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SOIC-8 to DIP-8
Package of 5
PCB for converting SMD SOIC-8 packages to through hole DIP-8 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SOIC-16 to DIP-16
Package of 5
PCB for converting SMD SOIC-16 packages to through hole DIP-16 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets. This adapter is also compatible with SOP-16 packages.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SSOP-16 to DIP-16
Package of 5
PCB for converting SMD SSOP-16 packages to through hole DIP-16 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SSI2140 to SSM2040
PCB for converting SMD SSOP-20 SSI2140 chips to through hole DIP-18 SSM2040 chips. This adapter makes the SSI2140 pin for pin compatible with the original IC. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, TQFP-64 to DIP-64 Wide
PCB for converting SMD TQFP-64 packages to through hole DIP-64 footprints with 0.9" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SOIC-14 to DIP-14
Package of 5
PCB for converting SMD SOIC-14 packages to through hole DIP-14 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets. This adapter is also compatible with SOP-14 packages.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SOIC-28 to DIP-28 Wide
PCB for converting SMD SOIC-28-Wide packages to through hole DIP-28 footprints with 0.6" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
PCB - SMD to Thru-Hole Adapter, SSOP-20 to DIP-20
Package of 5
PCB for converting SMD SSOP-20 packages to through hole DIP-20 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.
Please Log In to view prices
Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP
TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.
Please Log In to view prices
Integrated Circuit - 24LC32A/P, EEPROM, 8-pin DIP
24LC32A/P EEPROM in an 8-pin DIP package commonly used in Spin FV-1 projects. The Microchip Technology Inc. 24LC32A is a 4K x 8 (32K bit) Serial Electrically Erasable PROM capable of operation across a broad voltage range (2.5V to 6.0V). It has been developed for advanced, low power applications such as personal communications or data acquisition. The 24LC32A also has a page-write capability of up to 32 bytes of data. The 24LC32A is capable of both random and sequential reads up to the 32K boundary. Functional address lines allow up to eight 24LC32A devices on the same bus, for up to 256K bits address space. Advanced CMOS technology and broad voltage range make this device ideal for low-power/low-voltage, nonvolatile code and data applications.
Please Log In to view prices
Op-Amp - LM358, Dual, 8-Pin DIP
LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.
Please Log In to view prices
Regulator - LM317T, Adjustable Output, 1.5A, Linear Voltage Regulator
Linear regulator with an adjustable voltage range from 1.2V to 37V. This regulator can supply 1.5A of current making it a great option for power supplies.
Please Log In to view prices
Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
Please Log In to view prices
Evaluation Board - EVB2130-P, SSI2130 VCO, Sound Semiconductor, Fully Populated
The SSI2130 offers unprecedented performance and features, but its ultra-compact QFN package can present prototyping challenges. The EVB2130 eases evaluation by providing a PCB that allows comprehensive exploration of capabilities. The EVB2130-P is fully populated and ready for the bench. With the exception of the SSI2130, all components are through-hole for easy construction and experimentation. A on-board +5V regulator and 2.5V reference simplify external power connections, and pots are provided for mixer control, PWM, and VCO setup. Switches ease selection of saw ramp direction plus Through-Zero and Pulse Modulation. Features
  • PCB size: 108 x 82mm
  • External Power: ±12V
  • Inputs: Expo Freq 1V/Oct PWM In Aux 1 and 2 In FM In PM In Hard Sync Soft Sync
  • Outputs: Sine Saw Triangle Pulse Square Mix Out
Please Log In to view prices
Integrated Circuit - AS3340A, VCO, Alfa, 16-Pin Dip
The AS3340A is Alfa’s version of the CEM3340 IC. The AS3340A is a completely self-contained, precision voltage controlled oscillator, featuring both exponential and linear control scales and up to four buffered output waveforms: triangle, sawtooth, square, and pulse with voltage controllable pulse width. Full temperature compensation makes these VCOs extremely stable, and eliminates the need for a temperature compensation resistor. The highly accurate exponential and linear control inputs are virtual ground summing nodes, allowing multiple control voltages to be mixed within the device itself.
Also included is provision for hard and soft synchronization of the frequency, and an output for easy adjustment of high frequency tracking. Special care in the design ensures oscillation start-up under any power-on sequence and supply conditions.
An on-chip 7.4 volt Zener diode allows the device to operate off ±15 volt supplies, as well as +12, -5 volt supplies.
Please Log In to view prices
Audio Power Amplifier - LM380, Class-AB, 2.5W, 14-Pin DIP
LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.
Please Log In to view prices
Machine Pin Socket - Preci-Dip, Break Away, 1 Row, 15 Position
High quality single row machine pin sockets made by Preci-Dip. These sockets are the break-away type and can easily snap into smaller sizes such as 5 separate transistor sockets.
Please Log In to view prices