Integrated Circuits

Regulator - TC1044, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.
Please Log In to view prices
Regulator - TC7660S, Charge Pump DC-TO-DC Voltage Converter, 8-Pin DIP
TC7660S charge pump voltage converter in an 8 pin DIP package. The TC7660S device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10 kHz. Frequency is increased to 45 kHz when pin 1 is connected to V+.
Please Log In to view prices
Regulator - MC78L05, 5 Volt, Linear Voltage Regulator
MC78L05 5V Linear Regulator. Used in MOD® kits. The TI version is the LM78L05. This fixed-voltage monolithic integrated circuit voltage regulator is suitable for applications that required supply current up to 100 mA.
Please Log In to view prices
Regulator - L78L33, 3.3 Volt, Positive Voltage Regulator, TO-92
L78L33 3.3V regulator in a TO-92 package. The L78L33 three-terminal 3.3V positive regulator employs internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Features:
  • Output voltage of 3.3V
  • Output current up to 100 mA
  • Short-circuit protection
  • No external components are required
Please Log In to view prices
Regulator - LT1054, Voltage Converter w/ Regulator, 8-Pin DIP
LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.
Please Log In to view prices
Regulator - LM317T, Adjustable Output, 1.5A, Linear Voltage Regulator
Linear regulator with an adjustable voltage range from 1.2V to 37V. This regulator can supply 1.5A of current making it a great option for power supplies.
Please Log In to view prices
Regulator - 7805, 5 Volt, 1A, Linear Voltage Regulator
5V linear regulator with up to 1 amp of current in a TO-220 package. This style of regulator can be found in many power supplies and also modular synth circuits as well as some stomp boxes. These voltage regulators are monolithic integrated circuits designed as fixed−voltage regulators for a wide variety of applications including local, on−card regulation. These regulators employ internal current limiting, thermal shutdown, and safe−area compensation. With adequate heatsinking they can deliver output currents in excess of 1.0 A. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents.
Please Log In to view prices