Hardware

#3 x ¼” Phillips drive wood screws made of nickel plated steel. This style of round head screw is commonly used on Gibson® truss rod covers.

Genuine Bigsby® mounting screws. These wood screws are for mounting bridge plates to the top of the guitar body. These are the stock screws included with plates like P-GB-PLATE.

Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10

#4 x ½” slotted drive wood screws made of nickel plated steel. This style of oval head screw is commonly used on early Telecaster® pickguards including the Nocaster® and Esquire® guitars.

#6 x 1” slotted drive wood screws made of nickel plated steel. This style of oval head screw is commonly used on early Fender® tweed amps to secure the back panels. They are also the same type used for securing strap buttons as well as for mounting the bridge plate on early Telecaster® guitars including the Nocaster® and Esquire® guitars.

High quality single row machine pin sockets made by Preci-Dip. These sockets are the break-away type and can easily snap into smaller sizes such as 5 separate transistor sockets.

M12 x1.0 threading. Nut and washer set for panel-mounting jacks.

#6-32 threading, package of 4. Comes in 1/2" or 3/4". For male to female standoffs, see S-H170X

#8-32 x 3 ¼" chassis strap screw. Single piece.

#3 x ⅜” Phillips drive wood screws made of nickel plated steel. This style of oval head screw is commonly used on Gibson® pickguards, truss rod covers, and some humbucker rings.

4-40 Phillips round head machine screws made of solid brass. These brass round head screws visually match the screws found on vintage Marshall amplifiers. They are a great choice for restoration or replica builds. The 4-40 size works in place of original M3 screws that were used for the AC inlet, noval sockets, PCB and turret board standoffs, and the P-H1700 and S-HM100-A rotary selectors. These will also work well in many other types of projects. Brass round head screws are available in the following sizes: Diameter/TPI SKU 4-40 S-HSB4-X 6-32 S-HSB6-X 8-32 S-HSB8-12 Pairs with S-HBNX brass nuts and S-HLWX-B lock washers. Use with S-ASP4-X spacers for board standoffs. S-HBWX flat washers are also available.

Combination Drive, Nickel, 6mm, M3 metric, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Combination Drive, Colored Head Binding Screws, 6mm, M3, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These dress nuts feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is capped. These fit any 15/32-32UNS bushing but can also work with some M12 bushings.

20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:

• Round Pin
• 20 Position
• 2.54mm Spacing
• Breakaway

18-8 stainless steel sheet metal screws. These flat head #8 screws have a length of ¾” and are commonly used to secure cable clamps directly to the cabinet for RCA reverb tank cables used in vintage Fender® blackface and silverface combo amps. For the larger #10 screws often used with power cables, see S-HFS10-34.

Stainless steel M6 flat washers that are nearly identical to the chassis mounting washers used on many Marshall amps. These oversized M6 washers pair with 30mm M6 screws S-HSM6-1X30-SS to attach the amplifier chassis to the head cabinet. Fits any Marshall head that uses M6 screws. Also fits #12 imperial screws.

1" stainless steel Phillips head, flat top screw.

#10 steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. Made of 18-8 stainless steel.

#4 finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance.

18-8 stainless steel sheet metal screws with blunt tips. These pan head #6 screws have a length of 5/16” and are commonly used to secure 9-pin sockets and other hardware to the chassis of blackface and silverface amps. These are also used in some tweed amps for securing the fiberboard and other hardware to the chassis. For the larger #8 blunt tip machine screws found in vintage Fender® amps, see S-HBS8-38.

#6-32 x ⅝” Phillips drive machine screws made of nickel plated steel. This style of oval head screw matches the pickup and switch mounting screws found on Fender® guitars with countersunk holes on the pickguard.

Fully insulated quick disconnect connectors for use with spade lugs. These connectors are size .187” and fit wire gauges 16-22AWG. These connectors are simple to attach to speaker wires using a crimping tool such as S-T-CP412G.

Common replacement for Marshall heads and many other applications. The nut is free floating and will help to take care of problems with misaligned holes. Convenient cage design stops the nut from moving while tightening. Fits panels 0.064" to 0.105" thick with square holes cut 0.375" to 0.38".

• M6 Threading
• Panel Range .064”-.105”
• Fits 0.375" to 0.38" Square Holes
• Zinc Finish
• Sold Individually