Hardware

Genuine Hammand screws for use with diecast enclosures. These screws fit all Hammond diecast enclosures as well as any 6-32 UNC threaded enclosure. The thread length is 0.375”.

#6 x 3/8 zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

Self tapping Phillips panhead machine screw #8, zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but not necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

Steel, type A narrow. SAE washers have a tighter fit on the bolt and a smaller outside diameter. Designed for general purpose mechanical and structural use.

Lock washer for Fender® potentiometers. Package of 12.

Phillips panhead machine screw, 10-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

M12 x1.0 threading. Nut and washer set for panel-mounting jacks.

A threaded fastener made from austenitic stainless steels. It contains chromium creating an invisible surface film that resists oxidation making the metal corrosion resistant. If the surface layer is damaged, it rebuilds itself in the presence of oxygen.

Switchcraft shouldered hex nuts for ⅜”-32 UNEF-2A threaded bushings. These nuts include a rubber grommet for use in sealed systems and also add a unique look to any build such as pedals or amplifiers. The large nut (W-SC-DRESS-1) is intended for panel or chassis thicknesses of 0.05” through 0.09”. The small nut (W-SC-DRESS-2) is intended for panel or chassis thicknesses of 0.095” through 0.125”. Rubber grommet included.

20 position male pin headers with a 2.54mm (0.1”) pitch. These headers use round pins that are smaller than the standard square type and are perfect for use with IC sockets, breadboards, and machine pin sockets. The breakaway construction makes fitting them to projects simple. Features:

• Round Pin
• 20 Position
• 2.54mm Spacing
• Breakaway

Zinc t-nut. Used for fastening metal to products made of wood, particle board or plastic. Low carbon steel. Package of 5. Multiple sizes available.

Original Fender speaker mounting stud/nut set. These speaker mounting studs were used on countless amps of the '50s, '60s, '70s, and beyond. The reverse thread section screws into the baffle wood and the machine screw section holds the speaker in place using the included keps nuts.

• Used on early ’50s and ’60s vintage amplifiers
• Fits most vintage and modern amplifiers
• 1” of 8-32 machine head thread
• ¼” of reverse wood thread
• 1-½” overall length
• 8-32 keps nuts included

Fender part number: 099-2094-000

Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These nuts are made of a strong durable plastic and feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is not capped so they can thread past the top of the bushing. These fit any 15/32-32UNS bushing but can also work with M12 bushings.

Genuine Switchcraft ⅜” knurled nut commonly used on ¼” jacks. This nickel plated knurled nut has a ⅜”-32 threading and offers a clean look on builds using these nuts. The ⅜”-32 threading fits other hardware with matching threading such as CTS potentiometers.

Assortment of metal 'stand off' spacers. 20 pieces.

Fiber Shoulder Washer Overall Outer Diameter = 0.625" Center Hole Diameter = 0.385" sold in packages of 5

Mounting bracket for vintage fuzz PCBs. This bracket is an exact replica of the bracket found in the Italian made Vox Tone Bender V828 pedals. The mounting width for the board is 1.35” which fits the P-PC-FUZZ-JEN, P-PC-BEND-MKII-BRN, and any other vintage spacing (0.15”) stripboard. The PCB mounting holes are threaded for M3 screws (sold separately). The two potentiometer holes are spaced 1.95” center to center and fit potentiometers with ⅜” bushings or smaller.

Slotted dress nut for ⅜”-32 threaded bushing such as standard Switchcraft ¼” jacks and CTS potentiometers. These plated brass nuts add a sleek look to any amplifier, pedal or guitar. This style of nut has a similar look to slotted round nuts found on plexi Marshall amps.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.

PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.

Stainless steel pan head Phillips self-tapping screws. #6 X ¾" length. Good for use with #'s 3,4 and 5.

Fully insulated quick disconnect connectors for use with spade lugs. These connectors are size .187” and fit wire gauges 16-22AWG. These connectors are simple to attach to speaker wires using a crimping tool such as S-T-CP412G.

M8 x 0.75 threaded hex nut. For use on potentiometers, switches, and jacks.

#6 steel finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. Made of 18-8 stainless steel.