Enclosures / Chassis

Chassis box perfectly suited for effects pedals and other DIY projects.

4.40" x 2.38" x 1.06" D. Equivalent to Hammond P-H1590B.
Add 0.16" to enclosure depth for lid.

Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Measures 4.77" x 2.58" x 1.41". Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Genuine Hammand screws for use with diecast enclosures. These screws fit all Hammond diecast enclosures as well as any 6-32 UNC threaded enclosure. The thread length is 0.375”.

Short trapezoid shaped Hammond enclosure. This style is reminiscent of vintage fuzz pedals. Screws included. Key Features:

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Four 6-32 x 1/2” machine screws secure lid - into factory tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

Rugged, diecast aluminum alloy chassis box. Equivalent to Hammond's P-H1590A.

Fender® style narrow panel Tweed Deluxe™(5E3) chassis.

• Chrome plated steel, .06" thick.
• Screened white lettering
• 8-Pin (Octal) socket holes: 3
• 9-Pin (miniature) socket holes: 2
• Chassis Dimensions: 14 1/2" x 4 1/8" x 2 5/8"

*NOTE*- This chassis has replaced the “ground” switch lettering found on originals with “standby”

1.99″ x 1.99″ x 1.22″ (51mm x 51mm x 31mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590LBX enclosure. This enclosure is great for tap tempos and other utility pedals.

Hammond Mfg 20 gauge steel 12” x 8” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8" holes to allow installation of optional bottom plates).

Aluminum chassis. 0.04" thick. Dimensions shown are exterior dimensions. Features:

• Spot-welded heavy duty construction
• Natural finish

Does not include cover. See P-H1434-16

Wah pedal enclosure, bottom, and foot-pedal shell and hardware. Enclosure shell & foot pedal are cast aluminum.

5.72″ x 4.77″ x 1.55″ (145mm x 121mm x 39mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590XX enclosure. This large enclosure is great for bigger projects.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Hammond Mfg 20 gauge steel 7” x 5” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8" holes to allow installation of optional bottom plates).

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

The Gorva S90 is a high quality powder-coated take on the Hammond 1590BBM size enclosure with a focus on function and design. Features:

• Beveled top and rounded corners for high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Add 0.16" to enclosure depth for lid.

Spot welded heavy duty construction chassis. 0.036" thick. Dimensions shown are exterior dimensions. Does not include cover. See P-H1431-12 or P-H1431-12BK3

The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:

• Slightly beveled top and rounded corners for high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Diecast Aluminum Chassis Box, 7.40" x 4.72" x 1.30". Six included machine screws secure lid. Add 0.16" to enclosure depth for lid.

Hammond Mfg 20 gauge steel 6” x 4” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8" holes to allow installation of optional bottom plates).