You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-ECB-555Switch - Dunlop, Footswitch, DPDT, Solder Lugs, for MXR

Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.


Please Log In to
view prices
Click to read more
P-H1590N1Chassis Box - Hammond, Unpainted Aluminum, 4.77" x 2.6" x 1.39"

Depending on the manufacturer, this enclosure is usually very similar to a 125B.



Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.


Please Log In to
view prices
Click to read more
P-H1590XChassis Box - Hammond, Unpainted Aluminum, 5.7" x 4.8" x 2.1"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H551Switch - Carling, Footswitch, SPST, Off-(On), Screw Terminals

Carling, SPST footswitch, Off-(On), momentary, normally open with screw terminals. Note: Off-(On) switches may sometimes be referred to as Off-None-(On).


Please Log In to
view prices
Click to read more
M-PAS-CABLE-3Cable - Power All, Black Right Angle Extension Jumper

Included in the Power-All System and also sold separately, the Cable-Black/R allows the user to power over-sized effect units or units w/AC jacks in hard-to-reach places off of the Power-All Daisy Chain. The Cable-Black can be connected to any plug on any Power-All daisy chain, or directly to the PA-9 itself.


Please Log In to
view prices
Click to read more
P-ECB-004Power Supply - Dunlop, 18V A/C Adapter

The Dunlop 18V power supply for Dunlop effects will save you some money on batteries and get the right power to your pedal! Features Include:



  • 18 volts of regulated DC current
  • 2.1 mm x 5.5 mm plug with negative center


Compatible Dunlop pedals include:



  • Older Crybaby Multi-Wah
  • SW-95 Slash Wah
  • M108 10-band EQ
  • KFK1 10-band EQ
  • M117R Flanger
  • EVH 117 Flanger
  • DD11 Dime Distortion
  • M134 Chorus
  • M181 Bass Blowtorch


Plus many other pedals requiring an 18vdc power supply!


Please Log In to
view prices
Click to read more
P-ECB-003Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.



  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive

Please Log In to
view prices
Click to read more
P-H1590EChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
Please Log In to
view prices
Click to read more
K-998Effects Pedal Kit - MOD® Kits, Tone Attack, Active Tone Stack

Shape your sound with the Tone Attack. 12 o'clock settings give an approximate unity gain with the pedal. Rotate the treble or bass knob counterclockwise to cut the corresponding frequencies. Rotate these same knobs clockwise to boost the frequency bands. The master boost knob can be used to attenuate your signal or push your tone to screaming loud volumes. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. The Tone Attack operates on a 9V battery or AC adapter, which is not included. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.


Please Log In to
view prices
Click to read more
K-995Effects Pedal Kit - MOD® Kits, The Aggressor, Distortion
The Aggressor is a high-gain distortion pedal kit that delivers contemporary distortion with plenty of chunk and ear-splitting pitch harmonics. The distortion effect goes from subtle break-up to over-the-top molten distortion at maximum gain.

The Aggressor features true bypass, LED indicator, and a versatile tone control with a scoop/bump switch that shifts the mid-frequency response, allowing you to craft a tone that fits your style of playing. It works well with humbuckers and single-coil pickups, so you can turn any guitar into a lethal weapon capable of inflicting serious brain damage and spontaneous combustion!

MOD® Kits are designed to give novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy-to-follow instructions and use point-to-point wiring. A pre-drilled enclosure and all necessary parts are included.
Please Log In to
view prices
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts